0
You touch two hot wires together breaker box will not turn back on did you burn the breaker out?
Wiki User
∙ 14y ago
You might want to call an electrician... nothing usually happens when you touch two hots together.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How do you fix an outlet that is not working if it works when it is taken apart but not when it is is put back in the box?
if this is a regular 110 plugin, just replace it. I suspect that you are either shorting out the wire when it is folded back into the box or the wire has been flexed too much and when folded back into the box is creating a disconnect. In either case, check the box for scorch marks, the wire for weak points or breaks in the insullation, *and* replace the receptical.
What happens when two hot wires are connected?
Wiring to the circuit breakers is 220 volts. The circuit breaker box has 2 110 Volt lines. If you connect two black lines together from one side nothing happens. If the these two black wires are from different circuit breakers you may have a safety issue by back feeding the electricity. If you connect 2 different 110 volt lines you will end up with a short. This ends up as a 220 volt short.
Can you put in piggy back circuit breakers in a circuit panel?
The electrical terminology for this type of breaker is a tandem breaker. It is where two breakers circuits can be in the same one breaker slot in a distribution panel. On this type of breaker there will be two output for a circuit value of what ever the breaker is rated for.
What is the most likely cause of an underwater pool light continually tripping GFI if it does not appear to be an overloaded circuit?
The circuit that the GFI controls has a current leak on it. The leakage could be anywhere in the circuit.To trouble shoot the circuit first shut off the GFI breaker to the circuit in question. Then remove the load (pool light) from the circuit. Isolate the feeder wires with wire nuts on both the "hot" and neutral conductors.Turn the GFI breaker back on. If the GFI breaker does not trip when it is turned back on, the problem is not in the feeder wires. The tripping problem is caused by the light fixture. If the breaker does trip you will have to find where the moisture is getting into the underground conduit system.Remove the light fixture and try to completely dry the unit. This can be done with a heat gun by blowing hot air on the fixture to dry it out.Once you think the fixture is completely dry, without placing the fixture back in its placement in the pool, temporarily connect it to the feeder wires and check to see if the breaker trips. If it does not trip then you have corrected the problem.What is left to do now is to find out where the leak is that is letting the moisture into the fixture. Once found and completely sealed the fixture can be placed back into service.
How do you ground your meter box to your breaker box?
The grounding is done through the metal nipple that connects out of the back of the meter base and into the back of the breaker panel.
How do circuit breaker keep the wires in a electrical circuit from overheating?
A circuit breaker is designed to 'break' in a circuit if a short circuit (or other malfunction) occurs. This prevents overheating (or burn-out) of the circuit wires. In older systems, you would need to find which fuse wire has fused and replace it. In a circuit breaker, once the fault has been found and corrected, the breaker is simply switched back on.
How do you ground in a plastic box?
The only way to ground your system if you're using plastic boxes is to continue the chain by connecting your ground wires together--just as you would with the hot and nuetral wires--through the entire circuit all the way back to the whole house gound in the circuit breaker panel.
How do you put heart breaker brain teaser back together?
the same way you took it apart but backwards
If you cut the wires from the wire harness in a 1990 f150 what do you do to fix it?
what wires are they? If they are just regular wires like for lights or something, the best method is to solder them back together with rosin core solder and cover them with heat shrink tubing what wires are they? If they are just regular wires like for lights or something, the best method is to solder them back together with rosin core solder and cover them with heat shrink tubing
How can I find a short in my wiring that keeps popping the breaker?
The first thing to do would be to unplug everything that might be plugged into that circuit. It might be an external device that is tripping the breaker. If you know an electrician see if he will help you as thing can get complicated with this type of troubleshooting.Usually the wiring in the wall does not fault unless someone has driven a screw or nail into it. The fault will be in the junction box so look for burn marks inside the junction boxes. It could be as simple as a ground wire touching the "hot" terminal of a switch or plug that has just be changed out for a new one. If there was some DIY work done on that circuit, check that part of the circuit out first.The very first thing to do is to turn the breaker off, remove the electrical circuit from the breaker that is tripping and then turn the breaker back on to determine that it is not a faulty breaker. With the circuit wire removed from the breaker, the breaker should not trip. If it does change the breaker out for a new one.The second part of trouble shooting the circuit is going to entail turning the breaker on and off with exposed wiring open at junction boxes. If you are not confident that you can do this, hire an electrician. Trouble shooting this type of electrical fault is time consuming. I like to determine where the middle of the circuit is and open that junction box first. This will let you know if the fault is upstream or downstream from this junction box.Once you determine approximately where the middle junction box of the circuit is, it has to be opened and the wires removed from the device that is located in the box. Make a detailed diagram of how the device is wired into the circuit and what wires are spliced together in the back of the box that you are working on so that the box can be reconnected the same as before you took it apart. Once the wires are all seperated from each other, turn the breaker on and see if the breaker trips off.If it does not then the fault is downstream from this box. Put the wiring back together the same as it was and move on to the next box downstream and do the same procedureon that junction box. If the breaker trips then the wiring has a fault between the breaker and the box you chose to open the circuit at. Again put the wiring back together the same as it was and move on to the next box upstream and do the same procedure on that junction box. Continue with this same type of procedure until you find out what junction box connection is tripping the breaker.
How do you fix an outlet that is not working if it works when it is taken apart but not when it is is put back in the box?
if this is a regular 110 plugin, just replace it. I suspect that you are either shorting out the wire when it is folded back into the box or the wire has been flexed too much and when folded back into the box is creating a disconnect. In either case, check the box for scorch marks, the wire for weak points or breaks in the insullation, *and* replace the receptical.
How do you fix garage door sensor wires?
What is wrong with them? If they are cut, simply hook back together and tape them.
What happens when two hot wires are connected?
Wiring to the circuit breakers is 220 volts. The circuit breaker box has 2 110 Volt lines. If you connect two black lines together from one side nothing happens. If the these two black wires are from different circuit breakers you may have a safety issue by back feeding the electricity. If you connect 2 different 110 volt lines you will end up with a short. This ends up as a 220 volt short.
Can you put in piggy back circuit breakers in a circuit panel?
The electrical terminology for this type of breaker is a tandem breaker. It is where two breakers circuits can be in the same one breaker slot in a distribution panel. On this type of breaker there will be two output for a circuit value of what ever the breaker is rated for.
How do you get power windows to work after wires have been unplugged on a 1989 Eighty Eight Royal?
plug them back together
What parts do you need to make an iPod touch?
You break an iPod, then hire someone to put it back together.
Why dont phase and neutral exchange?
Phase wires are "hot" wires and are the current-carrying conductors. (These are the wires that will shock you if you touch them.). The neutral wire is basically there to carry the electricity back to the source. It is not normally considered current-carrying. If you switch these two wires, you might energize the metal of equipment, causing a dangerous shock hazard.
