To have flow of electricity, you must make a complete circle of metal (or other conductor of electrons). This is called a circuit. If at any time the circuit becomes broken, the current automatically stops, because the power has nowhere to go.
Connecting batteries + to - is said to be connecting them in series. The voltage from two batteries in series will be additave. So two 1.5 volt batteries in series will give you 3.0 volts.
Electrons have a negative charge. For that reason, electrons will always flow in the opposite direction of the current, which flows from positive to negative. Electrons will therefore move from a negative terminal to a positive terminal when we look at the load on a cell. Within the cell, the electrons will flow from the positive terminal to the negative terminal.
Assuming neither battery is used to start the engine, simply connect the positive (+) terminal of the first battery to the positive terminal of the second battery. Then connect the negative (-) terminal of the first battery to the negative terminal of the second battery. Connect the load circuit to the positive and negative terminals of one of the batteries as usual. You may want to charge the batteries separately before making the connection, since connecting a charged battery to a discharged battery will result in a very large current flowing from the charged battery to the discharged battery, possibly damaging the wiring or either battery.
Connect the positive terminal on one battery to the negative terminal on the other with heavy wire and battery clamps. Connect the remaining positive terminal to the metal chassis of the tractor, and run the remaining negative wire to the items to be powered, with any luck at all, through a fusebox.
the positive side, the negative side is usually just a ground
Note: When interconnecting A200 batteries (cells), they must be identical in voltage and amp rating! Batteries may be connected in series. The positive terminal of the first battery is connected to the negative terminal of the second battery; the positive terminal of the second is connected to the negative of the third, and so on. The voltage of the assembled battery is the sum of the individual batteries. The batteries are connected: + to - to + to - to + to -, etc. The capacity of the battery is unchanged. Batteries may also be connected in parallel. The positive terminal of the first battery is connected to the positive terminal of the second battery, the positive terminal of the second is connected to the positive of the third; the negative terminal of the first battery is connected to the negative terminal of the second battery, the negative terminal of the second is connected to the negative of the third and so on. The batteries are connected: + to + to + and - to - to -. In this configuration, the capacity is the sum of the individual batteries and voltage is unchanged.
One terminal is positive and the other terminal is negative. The positive terminal is slightly larger.
Look for a + by the positive terminal and a - by the negative terminal, or red for positive, black for negative. Some batteries have the positive terminal protruding and the negative terminal flat. Or you can get a meter that will tell you which is which,
The positive terminal of the battery would be connected to the positive terminal of the ammeter. The load would then be connected between the two negative terminals, positive side of the load being connected to the negative side of the ammeter.
What is your question?
To jump start an engine via the battery; the remote battery and the host battery, being of the same voltage, should be connected in parallel. That is positive terminal to positive terminal, negative to negative.
I can if I charge 2 of them at a time. Most 24 volt chargers also have a 12 volt setting. What is hard to find is a 32 volt charger. We can charge a 12V battery with 24V charger, by connecting two 12V batteries in series i. e. the negative terminal of the first battery is connected to the positive terminal of the second, now the charger positive terminal is connected to the first battery positive terminal and the negative terminal of the charger is connected to the negative terminal of the second battery.
You just connect them in Parallel. Two 12 volt batteries connected in parallel will output 12 volts. Two connected in Series will output 24 volts. Just connect the negative terminal on the first battery to the negative on the second battery. Then connect the positive terminal on first battery to the positive on the second battery. Connect the cables to the second battery, positive to positive and negative to negative. Click the link for a diagram.
plus is the positive terminal (cathode) minus is the negative terminal (anode)
In parallel. IE: Positive terminal to positive terminal, Negative terminal to negative terminal. Same as boosting a car batery.
Normally only two, a positive and a negative terminal.
Connecting batteries + to - is said to be connecting them in series. The voltage from two batteries in series will be additave. So two 1.5 volt batteries in series will give you 3.0 volts.