As little as possible, since the ammeter must be inserted in the circuit,
and the current it measures must flow through it.
A resistance opposes the flow of electric current. So, in terms of conductivity, obviously a low resistance is better. Besides, heat is developed as a result of resistance, which is not desireable in some appliances. However, the choice is different depending upon the instrument or appliance. For instance, heater requires materials of much higher resistance than bulbs.
Surely the electrical resistance of a heater is lower than that of a lightbulb, since the heater uses much more current?
The second comment is correct - a heaters resistance is typically much less than that of a light bulb, meaning more current will flow at a specified voltage, thus more power is used by the device. Taken another way, a 13 watt lightbulb will have a much higher resistance than a 100 watt light bulb, because they are both made to operate on 120 volts, but one uses more power than the other.
To answer the original question, though, it depends on the purpose of the resistor. If you wish to limit current flow to the base of an amplifier circuit, you would use a relatively high resistance. If you used too high a resistance, this can negatively impact the amplifier's ability to amplify, so perhaps a lower resistance resistor would be appropriate (again, depending on the use!). But a very low resistance may increase the base current flow to unnecessary levels, thus wasting energy. If this is in a battery operated device, this would not be ideal either, so a higher resistance may be appropriate.
Sometimes it doesn't really matter, other times it really really does. A specific example needs to be given for a specific (true) answer to be given.
Resistance is measured in Ohms with an Ohm meter or multi meter set on Ohms. Maybe you should rephrase your question. -Bob
low resistance.
low
Transistor=Transfer+Resistor. When Transistor operates in active region its input resistance is high and output resistance is low. So,We can consider transistor as a device which transfers its resistance from high to low. And by this property transistor amplifies input signal.
No, it is desirable for a battery to have a low internal resistance.
An ammeter is a low voltage voltmeter in parallel with a small resistance resistor. Current flow through the resistor creates a voltage drop across it which is then measured by the voltmeter.
A Cadmium Disulphide cell. (aka Cds cell)
Because it is a metal so has lots of free electrons which when connected to a circuit detach from the atoms and move around the circuit. This produces a high current, so resistance will be low as current is high.
Usually low resistance is better.
Transistor=Transfer+Resistor. When Transistor operates in active region its input resistance is high and output resistance is low. So,We can consider transistor as a device which transfers its resistance from high to low. And by this property transistor amplifies input signal.
It is related to damping in the circuit using a resistor. Q is inversely proportional to the resistor(R). So if the value of resistance is high, there is a greater damping and the value of Q will be low. if resistance is low, there is small damping and Q will be high. when Q is high(low damping) the graph of voltage across resistor against frequency will be sharp at resonance and the bandwidth will be small when Q is low(high damping) thee graph will be less sharp as the bandwidth will be large. Go do some research on the graphs and the formula of Q factor to understand it better.
No it is not. A resistor has a known resistance that is less than infinity. A switch has a resistance of either infinity when it is open or low when it is closed
Graphite is low resistance of electricity...
By attaching a resistance in parallel connection with the galvanometer. Or when a low resistor connected in parallel with galvanometer ,the galvanometer is converted in ammeter. and the resistor is called shunt resistance.
Gold has a low resistance, which means it is a good conductor of electricity. This property makes it useful in various electrical applications where low resistance is needed for efficient conduction of electricity.
Good conductors have low resistance
A low resistance bulb has a thicker filament.
On a multimeter, a high resistance would indicate a high Ohmic value and a low resistance would indicate a low Ohmic value. Specific values would be relative to device you are measuring.
Heater blower resistor is what controls the low medium high speeds...
It depends on the application. Voltmeters have a high internal resistance, while ammeters have a low internal resistance.