0
What is the use of the tail stock sleeve in centre lathe machine?
Wiki User
∙ 12y ago
Tails tock sleeves are used on CNC lathes. It is the equivalent to a tail stock quill on a center lathe but in this case it uses hydraulic pressure to move it in and out of the tail stock.
The function of both tail stock sleeve or quill is to clamp the workpiece by means of a center that is inserted into the sleeve or quill. On a center lathe it is used for drilling also but not on a CNC lathe.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What type of sleeve used for drill chuck used in lathe?
For drilling in a lathe, "Drill Sleeves" also known as "Drill Quills" are used and they are set into the tail stock quill for drilling operations.
How a lathe machine is specified?
A lathe machine is specified by-1.The maximum diameter of the workpiece that can be operated on the machine.2.The distance between the headstock and the tail-stock of the machine.3.The length of bed of the machine.
What causes the lathe machine taper problem?
Taper problems on a lathe can be caused by many things. Below are the most likely possible causes and solutions:Misaligned tail stock- In most cases the tail stock can be realigned with its setting screws- Worn tail stock slides - Send for repairMisaligned Head stock- The head stock can be re-alignedMisaligned bed- The entire machine should be leveled againWorn bed ways- The machine should be sent for regrinding the beds
What do you mean by spindle in lathe machine?
The spindle of a lathe is a rotating hollow tube within, and protruding the head stock and to which a chuck, drive plate or facing plate attaches and rotates to enable machining. It is housed within the head stock in bearings and has some gears around it which is driven by other gears which in turn is driven by an electrical motor.
What is the difference between a milling machine and a lathe?
A milling machine basically look like a drill press, but with the ability to move the work piece sideways. A lathe clamp and spin the work piece horizontally and use a stationary tool bit to cut and shape the work piece.
What is the main features of the Centre Lathe in the machine shop?
Compound Slide, head stock tail stock tool post the spindle
What type of sleeve used for drill chuck used in lathe?
For drilling in a lathe, "Drill Sleeves" also known as "Drill Quills" are used and they are set into the tail stock quill for drilling operations.
What is distance between centers in lathe machine?
All lathes could be considered "centre lathes." You turn "between centers." There's also a tool called a "machining center," but those are for computerized milling, normally of metal.
How a lathe machine is specified?
A lathe machine is specified by-1.The maximum diameter of the workpiece that can be operated on the machine.2.The distance between the headstock and the tail-stock of the machine.3.The length of bed of the machine.
What causes the lathe machine taper problem?
Taper problems on a lathe can be caused by many things. Below are the most likely possible causes and solutions:Misaligned tail stock- In most cases the tail stock can be realigned with its setting screws- Worn tail stock slides - Send for repairMisaligned Head stock- The head stock can be re-alignedMisaligned bed- The entire machine should be leveled againWorn bed ways- The machine should be sent for regrinding the beds
What is the difference between a milling machine and a lathe?
A milling machine basically look like a drill press, but with the ability to move the work piece sideways. A lathe clamp and spin the work piece horizontally and use a stationary tool bit to cut and shape the work piece.
What do you mean by spindle in lathe machine?
The spindle of a lathe is a rotating hollow tube within, and protruding the head stock and to which a chuck, drive plate or facing plate attaches and rotates to enable machining. It is housed within the head stock in bearings and has some gears around it which is driven by other gears which in turn is driven by an electrical motor.
How are lathe machines installed?
Lathes are installed using the following method: (The method may slightly vary from person to person)The bolt pattern on the head- and tail stock pedestals are measured and matching studs are set into the floor onto which the lathe will be installed.An electrical line is routed to the location where the lathe will be installed for supplying it with power.The lathe is placed on shifting skates or machine rollers and moved over its permanent location.Jacks are used to lift the lathe off the rollers and placed over the studs and down onto the floor. The jacks are then removed.A set of spirit levels are placed on the lathe's beds and leveling of the machine is done by setting the jacking bolts located on the pedestals.Once the machine is leveled, a washer and nut is placed on each stud and the machine is bolted down.A further option might be used by cementing between the floor and the pedestal bases of the lathe to enhance sturdiness.Power is connected to the lathe and all the oil levels are checked and filled if necessary.The lathe is started and tested.An alternative to setting studs, using the lathe's jacking bolts and cementing is the use of adjustable rubber foot pads. The machine is moved to its location and jacked up. The foot pads are installed into the pedestal mounting holes then the lathe is set on the floor and leveled.
What are the parts and functions of tail stock?
Tail stock is a part of lathe ,which is used to support the lengthy job.
Where does vibration occur most in a lathe machine?
Some major sources of lathe vibration are as follows: 1.) The stock you are turning is not centered properly, or has a lopsided mass. This has the same effect of to much clothes on one side of your wash machine during spin cycle. You can cure this by slowing down the speed you turn at until the roughed stock is more centered. 2.) Take a look at the head stock on your lathe, if it has worn bearings, if the pulleys are out of line or your belt is worn, you will most likely get vibration. 3.) Look at the floor your lathe is on. Is it solid? Cement is the best surface, an flex in your floor will result in lathe vibration. 4.) Look at the stand your lathe is on, is it solid, is it true. A level will let you know if youre base is sagging under the weight of your lathe. Make sure your lathe base is solid and not attached to surrounding walls. The common fixes: Bring your head stock and tailstock together until they touch. Do they line up perfectly, if not you may have a lathe base or floor that is sagging under the weight. Spin the lathe by hand. Is it smooth? If its rough or bumpy chances are you have worn bearings that need to be replaced. Use a straight edge to make sure all belts and pulleys are in line. Being off center will cause vibration or can cause un-even wear of the belts which in turn will cause vibration. If the belt is worn replace it. Add some weight to your base. The lathe is heavy so any vibration is sent right through your base and magnified. Add weight makes it harder for the lathe to move around and will decrease vibration of an out of round piece of stock.
When was Nottingham Arabidopsis Stock Centre created?
Nottingham Arabidopsis Stock Centre was created in 1991.
What is bed length in lathe?
The bed length of a lathe is the total length of the bed way from where it starts to (close to the headstock) to where it ends. When a lathe is advertized for sale it would show for example: 200mm x 1000mm or 8" x 40". The 200mm or 8" describes the "swing" of the machine and the 1000mm or 40" describes the workable distance between the chuck and center. This should not be confused with the bed size of a lathe as the bed houses the tail stock and therefore the distance is shortened.
