0
What is the rough size opening for a 16 ft x 8 ft garage door opening?
Wiki User
∙ 8y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is the size of a Standard door opening to the garage?
32" is typical.
Can a Tahoe fit in a one car garage?
It would depend on the size of the one car garage and garage door opening.It depends on the size of the garage. Not all one car garages are the same size.
What is the size of the rough opening for a 42 inch wide exterior door?
The rough opening width for a 24" door is 26-1/2" The rough opening height for a 24" door is 26-5/8" Rough openings are 2" wider and 2-1/2" taller than the actual door. This allows room for the door frame and adjustment.
What is the rough opening requirement for an interior door that is 3 foot with a frame size of 3 foot 1-58?
The rough opening of an interior door is two inches wider than the width of the door and two inches higher than its height. Thus your rough opening width is 38". A typical interior door has a height of 80" which would require a rough opening height of 82" but check your door to ensure that is theheight.
What is the rough opening size for a 72 bifold door?
R.O. is normally 2-2 1/2 inches greater than door size.
Rough opening 30''by 82'' what size door?
28 inch is all you can get in that. Any door needs a minimum of 1 1/2 more than the door size.
What is the size of a rough opening for a 4X4 door?
4'1 1/2" by 4' 1 1/2"
What is the rough opening of a 36 inch door?
Remember 36" is the width of you door slab. If you can measure the door you want to frame in then take the measurement and add 3/4" to it so you can still have room on the side to shim it properly. If you don't have the door but know which one you want, go to the store and the door will normally have the rough opening size on the label.
What measurements do I require to replace walk-in garage door?
Add 2 1/2" to the width and height of your "call" size. If you have a 3'o" x 6'8" you would need a rough opening of 38 1/2" x 82 1/2" .
What size door fits in a 82.5 X 32.5 inch hole?
standard height door (80" tall) 2' 6" wide door. Rough opening width is oversized 2"
How do you measure exterior frame door width?
You are supposed to measure the "rough" opening. This is distance from the studs that line the door opening. (not from the door frame itself) Top to bottom then from side to side. If you already have a door there and are just replacing it then you can just measure the door and get one of the same size. Good luck.
Garage Door Installation?
Installing a garage door can be done with some basic tools, and an attentive helper The basic components that are needed to install a garage door are an opening that’s sized correctly, the door, and a set of garage door hinges. The size of the rough opening for a particular garage door will most often be specified in the installation instructions that come with the door, and the existing hinges can be used so long as they are in good repair. If a coil door with a spring return is being installed, the existing pivot hinges will not be needed, and can be removed. An over-sized opening can be furred using any thickness of lumber that will build out the jamb sides and the head to the correct rough dimensions. Sectional doors will ride on rails that require solid wood backing as a mount, and any build-out of the opening must be solid in order to secure the lag bolt that attach the rails. Where an overhead coil is being installed, the garage door header will serve as a suitable mounting surface for the coil. Installing a sectional door or a coil door should be done by a professional, and not attempted by anyone who is not familiar with the operation of these doors. With wood garage doors, the installation begins by standing the door in the opening, with several ½” shims to elevate it from the garage floor. With the door in place, the hinges can be installed and through-bolted to the garage door using machine bolts with nuts and washers. Lag bolts are not recommended for attaching the hinge plate to the garage door, since these can work free in time. Once the hinges are secured to the jamb and the door, the door is raised to fully open, and braced in the open position using a 2”x 4”. The springs can be installed and the keeper clips snapped in place to ensure the springs are secure. Once the final spring is stretched on the hinges, the door will self adjust to the correct open position. If an automatic garage door opener is to be installed, the spring tension may have to be adjusted in order not to tax the opener. A few test cycles with the opener will most often resolve any issue related to the spring tension.
