0
What is the proportion of oil sand mix to be use for the foundation of refinery tanks?
Wiki User
∙ 11y ago
Bituminous Sand.
Flat steel based tanks at ground level should be bedded on bituminous sand, provided by the contractor. It should be in accordance with BS 2654 (now EN 14015:2004), produced by hot mixing the following proportions by mass:
a). 9 +/- 0.5% non-toxic cut black bitumen (i.e. fluxed with kerosene and not creosote).
b). 10 +/- 1.0% filler: either limestone dust passing a sieve on nominal aperture size 0.075 mm(75 microns) complying with BS 410, or Portland cement.
c). 81 +/- 1.5% clean dry washed sand with the properties given in table 2 of BS 881, Part 2: 1973.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What is the mix proportion of concrete?
The standard mix is 123 That is one cement two sand three gravel
Why river sand is used for foundation of buildings below?
Benefits of Sand layers below the Foundation PCC... 1. River sand layer has more SBC compare to clay or silty soil. Hence it helps the footing load distribute to sub soil uniformly 2. As the SBC of river sand is more it reduces secondary settlement of the structure to some extent ( never zero) 3. It create a uniform leveled surface to take the PCC or Footing 4. Compare to clay or silty soil it reduces Termite entry to the structure 5. If the soil is of having more acidic or alkali sand layer prevent the structure from the deterioration ( increase life period)
Why would you need to pump sand under your house?
generally they pump sand or gravel under house for the footers and the foundation. the sand or gravel helps to make the concrete they are going to pour shift or move less than what it would if it where just on the ground/ dirt, it also creates a barrier from the moisture in dirt. usually depending on state building codes the thickness of the sand or concrete should be between 4" to 12". In cold weather they like to use sand because it does freeze as hard as soil.
What is the purpose of a foundation?
a good strong foundation ensures good strong stable ground for a good strong and lasting structure. -- if you build a house on sand and the sand around one of the corners of the house washes away due to rain water falling off your building the building will begin to sink in that corner and the result will eventually begin cascading further along the buildings edges and sides until the entire building is consumed by leaning caused by unstable ground.
What is soil sampling in civil engineering?
From my understanding soil samples are taken to consider the possible ways a foundation of a building will be layed. That sort of thing. Hope this helps.
What is the proportion of bed concrete in foundation?
The proportion of the bed mortar should be 4:1 for the sand : cement.
What proportion of the earth's deserts are sand?
About 20% of deserts are sand.
Would a foundation of sand be a good place to build a building?
No. Sand is not rigid.
Where can you get a 400 BBL tank or 500 BBL tank?
I bought mine from OP Tanks in Ogden, Utah. They also make 210 BBL Tanks, 300 BBL tanks, mud tanks and sand tanks. You can see products at http://www.optanks.com
What is the proportion of concrete?
The standard mix is 123 That is one cement two sand three gravel
What is the density of sand that used to strip foundation?
unit weight of sand used in strip foundations is 1700kg per cubic meter
What is the mix proportion of concrete?
The standard mix is 123 That is one cement two sand three gravel
What is the difference between loam and sand soil?
Sandy soil is soil that has a high proportion of sand in it. Loam is a predetermined soil mix. For example a loam might be 40% silt, 40% sand and 20% clay.
What is the ratio of cement water and sand in rcc?
what is ratio of rcc work machine foundation
Whats the 124 proportion in concrete technology?
The 124 proportion in concrete technology is 1 bucket of cement to 2 buckets of sand to 4 buckets of aggregates to 1/2 bucket of water.
What do newts need in their tanks?
you could have a plant pot with a hole in, stones. soil or sand plant water area.
What is mix design proportion for M30?
1:1:2 (1 cement: 1 sand: 2 coarse agregate)
