0
What is the difference between back pressure steam turbine and condensate steam turbine?
Wiki User
∙ 14y ago
In a back pressure turbine all available energy from the inlet steam is NOT used to generate power; steam exhausts at a tangible pressure and is then used for, usually, heating or chemical processing. In a condensing turbine, all the inlet steam does mechanical work right down to the lowest pressureafter which it is condensed in a heat exchanger
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What is the difference between turbine turning gear and barring gear?
both are same using for rotating the turbine initially
What is the difference between generator turbine?
RADITOR * Small generators either air cooled or water cooled 2 stroke. Autos are mainly 4 stroke and the majority watercooled.
The gross head in turbine installation is difference of level between?
it is difference between the water level from head race and tail race
Why PRDS used in thermal power plant?
they work parallel to power generating turbines. The only difference between prds and turbine is that prds give only process steam by simply reducing the pressure of incoming steam while a turbine generates power out of that pressure reduction, and also give left out steam as process steam.
What is difference between radial flow turbine and axial flow turbine?
in a radial flow turbine the steam enters the turbine in the direction of its radius and leaves it in the direction of the axis of the shaft. in a axial flow turbine the steam enters the turbine in the direction of the axis of the shaft and leaves the turbine in the same direction.
What is the difference between back pressure and absolute pressure in steam turbine?
Back pressure is the small amount of vacuum that is created when the used steam condenses from the turbine back into re-usable water.
What is difference bw condensing and non condensing steam turbines?
A condensing turbine uses all the energy from the steam going from high pressure turbine to secondary turbine to condensing turbine then sends the condensate back for reheating. where a non condensing turbine just uses the high pressure aspect of the steam then returns the low pressure stream back to be reheated. Condensng turbines utilises the entire available drop from high pressure to the vacuum in the condenser; a back pressure turbine only utilises only the top part, whereas an exhaust steam turbine utilises only th bottom part of the pressure drop. Hope that helps.
What is the difference between 500MW and 600MW power station?
The ans is with respect to Thermal Power plants: the basic difference between a 500MW plant and 600MW palnt is in the turbine design. the 600MM turbine has 1 HPT, 1IPT and 2 LPTs, 2 Condensors and a generator. the 500MW turnbine has 1 HPT, 1IPT and 1 LPT, 1 condensor and a generator. HPT: high pressure turbine IPT: intermediate pressure turbine LPT: low pressure turbine
What is the difference between volute centrifugal pump and turbine centrifugal pump?
voloute convord the pressure into volicity and the mixtur of propallere and impeller is called turbine pump
What is intermediate pressure turbine?
Some varieties of gas turbine engines (e.g. RR Trent and RB211) have 3 concentric rotating shafts. Each shaft connects a compressor with a turbine. The low pressure compressor, or fan, is driven by the low pressure turbine. The high pressure compressor is driven by the high pressure turbine. Between the low and high pressure compressors there is an intermediate pressure compressor and, guess what... it's driven by the intermediate pressure turbine.
What is mix pressure turbine?
mix-pressure turbine
What is the difference between turbine and machine?
the machine is the one that operates or makes the turbine work. the machine is the one that operates or makes the turbine work.
Difference between hogger and ejector of condensing turbine?
A Hogger is a device to remove the Air from Turbine inside for creating initial vaccume for start up the turbine means create negative pressure inside Turbine or say creates less pressure than atmospheric pressure in Turbine.An Ejector is a device used in Power plant to remove Undissolved gases from Condenser to avoid any harm to system from these gases.If any correction is required pl. correct it.
What is the difference between turbine turning gear and barring gear?
both are same using for rotating the turbine initially
What is the inlet pressure of a condensate tank?
It can be at any pressure less than the main steam pressure. I've operated steam systems with condensate tanks at widely varying pressures. The pressure a condensate tank, (which condenses some steam, but typically takes returns from steam traps) is wholly dependent on the system is installed in. Some heating system condensate tanks are designed to handle no more than 30 psig (minimum design requirement) yet take condensate at 1 or 2 psi from the steam traps. Other high pressure production lines operating at 50 - 100 psig could discharge to a tank at 50 - 100 psi, though the actual pressure would be reduced by the length of pipe transferring it to the tank. And the highest pressure I've operated a condensate system at was 600 psig, the steam system drew the steam for process from an extraction stage on the turbine at nominally 600 psi, though at low loads it was typically a much lower pressure.
What is the wheel chamber pressure in turbine?
Resistance offered by turbine to the steam
What is the difference between generator turbine?
RADITOR * Small generators either air cooled or water cooled 2 stroke. Autos are mainly 4 stroke and the majority watercooled.
