0
The camshaft interrupter magnet also known as the camshaft positioning sensor uses the magnetic field created by the magnetic pole piece to relay the camshaft positioning data to the engine control computer to start accurate, split-second ignition timing adjustments.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How do you replace your Camshaft Position Sensor Interrupter Magnet in your 1994 buick lesabre?
The interrupter magnet is normally replaced by removing the camshaft gear as the magnet is inserted through the back side of the gear.
Where is the camshaft interrupter magnet on a 4 cylinder 1997 Chevy S-10?
in the distrubutor i believe
What could be the problem if you get codes that say intermitted signal lost at camshaft sensor when you replaced the distribtor with a new camshaft?
Camshaft sensor interrupter will send that code.
What does the camshaft interrupter on a 1989 Buick Lesabre do and where is it located?
It should be behind the camshaft postition Sensor in the timing box attached to the end of the CamShaft. It allows the computer to know where the cam shaft is in order to properly inject fuel to the proper valve at the proper time.
What is the GFCI?
A "GFCI" is a ground fault circuit interrupter. For more information see the link below.
What is an example of a circuit interrupter?
An example of a circuit interrupter would a fuse or circuit breaker.
What is an interupter in an sentence?
The person in the red shirt was the interrupter in the meeting. This is the sentence that uses the word interrupter.
Where is the camshaft sensor in 2004 Ford Freestar located?
Look underneath the engine where the serpentine belt is located, you can see it by a toothed round gear, it works as a magnet.
When replacing camshaft position sensor on 2004 dodge neon is it necessary to replace or adjust the target magnet?
sometimes yes it could be the problem for the vehicle not starting look for cracks or rub marks on the magnet if that doesnt solve the no start problem with new magnet and sensor check the wires for shorts or bad grounds.
How is the comma or dash used as an interrupter in this sentence?
In this sentence, the comma or dash can be used to set off an interrupter phrase that provides additional information but is not essential to the main clause of the sentence. This interrupter phrase adds clarity or emphasis to the sentence without changing its core meaning. The choice between a comma and a dash depends on the writer's preference for style or the desired level of emphasis on the interrupter.
How do you change camshaft sensor 2003 stratus 2.4 liter?
Follow the below steps to replace the camshaft sensor 2003 stratus:1) Loosen the two bolts securing the air inlet resonator, the large plastic component that the air filter outlet tube connects to, using a ratchet and socket. Now, pull the air filter outlet tube from the air filter housing.2) Pull the oil separator tube from the air filter outlet tube using a slight twisting motion. Remove the air filter outlet tube and resonator from the engine compartment, exposing the camshaft position sensor.3) Unplug the camshaft position sensor's wiring harness. Remove the screws securing the camshaft position sensor using a ratchet and socket.4) Remove the screw securing the camshaft magnet to the camshaft using a ratchet and Allen-bitsocket. Then, pull the magnet from the end of the camshaft.5) Line up the dowel pins on the new camshaft magnet, which comes with the new camshaft position sensor, with the locating holes on the end of the camshaft; then, place the camshaft sensor back onto the cylinder head in the same position it was in prior to removal.6) Press the air filter outlet tube onto the outlet on the air filter box, then tighten the hose clamp to between 20 and 30 inch-pounds.Guide the resonator's hose onto the inlet on the throttle body and tighten the hose clamp to between 20 and 30 inch-pounds.7) Set the resonator in place on top of the engine, aligning its bolt holes with those on top of the engine.
What is a camshaft positioning sensor?
Modern electronically controlled engines use a sensor to keep track of the position of the pistons for spark timing. Since all the moving parts in the engine are mechaically linked, only one sesor anywhere in the system can provide the required information. Most systems put this sensor on the crankshaft. But a sensor on the camshaft would also work. The sensor itself is a simple magnet and pickup coil. The coil sends out a pulse every time the magnet passes it.
