0
In a diode modulator the negative half of the am wave is supplied by the?
Wiki User
∙ 8y ago
tuned circuit
Anonymous
Add your answer:
Earn +20 pts
What property of a diode enables it to convert ac to dc?
A diode allows electrons to pass only in one direction. During the negative half cycle of an alternating current the diode will not allow electron current to pass. It is like a one way valve. This property of diode enables it to convert AC into pulsated DC
How does a diode act as a half wave rectifier?
The diode is a unidirectional device it allows current to pass through it only when it is forward biased and does not allow when reverse biased when ac signal is supplied in the positive half cycle of the ac wave signal the diode will b in forward biase n in the negative half cycle it is in reverse bias .Hence it allows only the positive half cycle current to flow through it the resultant wave form will b only in one direction ,i.e,dc signal with ripples. only half of the wave is rectified hence it acts as a half wave rectifier
Why full eave rectifier rectifies negative half cycle?
the rectifier is Mainly used to convert the Ac current into DC current .In rectifier there are two diodes or (4 Diode In full wave bridge rectifier )are use is to conduct the current one is connected in forward bias(i.eD1) and the other is connected in reveres bias(i.eD2). As we know that the diode is conduct the current throw it When it is connected in forward bias . now when the voltage is applied to the circuit the the AC Current is start to flow throw circuit and in Positive half cycle of Ac current the Diode is Allow the current Pass throw it and during the Negative half cycle the Diode D2 is allow the current pass throw it and in these way the rectifier rectifies positive As Well As the negative half cycle
What is the difference between a half wave rectifier and a negative clipper?
As far as general principles apply, they both perform the same function: using a diode.
A diode converts AC to pulsed?
If you put a diode in series with an AC sine wave that goes plus and minus, it will cut off either the positive or negative portion of the waveform, depending on the direction of the diode in circuit. So in effect you have a pulse equal to one half cycle of the sine wave.
What property of a diode enables it to convert ac to dc?
A diode allows electrons to pass only in one direction. During the negative half cycle of an alternating current the diode will not allow electron current to pass. It is like a one way valve. This property of diode enables it to convert AC into pulsated DC
How does a diode act as a half wave rectifier?
The diode is a unidirectional device it allows current to pass through it only when it is forward biased and does not allow when reverse biased when ac signal is supplied in the positive half cycle of the ac wave signal the diode will b in forward biase n in the negative half cycle it is in reverse bias .Hence it allows only the positive half cycle current to flow through it the resultant wave form will b only in one direction ,i.e,dc signal with ripples. only half of the wave is rectified hence it acts as a half wave rectifier
Why full eave rectifier rectifies negative half cycle?
the rectifier is Mainly used to convert the Ac current into DC current .In rectifier there are two diodes or (4 Diode In full wave bridge rectifier )are use is to conduct the current one is connected in forward bias(i.eD1) and the other is connected in reveres bias(i.eD2). As we know that the diode is conduct the current throw it When it is connected in forward bias . now when the voltage is applied to the circuit the the AC Current is start to flow throw circuit and in Positive half cycle of Ac current the Diode is Allow the current Pass throw it and during the Negative half cycle the Diode D2 is allow the current pass throw it and in these way the rectifier rectifies positive As Well As the negative half cycle
What is the difference between a half wave rectifier and a negative clipper?
As far as general principles apply, they both perform the same function: using a diode.
What is the working principle of halfwave rectifier?
Where a single diode is used as a rectifier you get halfwave rectification when the sinus wave is going positive the diode will conduct but in the negative half of the cycle it will block the current flow so the result wave form will be only the positive half that will be available for half the period of the cycle the other half will be 0 Volt
Why the negative half cycle cannot pass through the diode?
When the diode is reverse biased a depletion zone is formed at the junction between the cathode and anode, that lacks current carriers (it has neither electrons or holes). Without current carriers, the diode acts as an open circuit, blocking current flow.
A diode converts AC to pulsed?
If you put a diode in series with an AC sine wave that goes plus and minus, it will cut off either the positive or negative portion of the waveform, depending on the direction of the diode in circuit. So in effect you have a pulse equal to one half cycle of the sine wave.
What effect does an open diode have on the output voltage of a half wave rectifier and on a full wave rectifier?
An open diode will result in no output from a half wave rectifier, and an open diode will cut the output of a full wave rectifier in half.
Why we don't get negative half cycle in rectifier outpus?
We don't get negative half cycles at a rectifier's output only in a positive supply.If the supply is for a negative voltage, then there will be no positive half cycles at the output.Read a bit more about rectification.We don't get negative half cycle in rectifier outputs because the negative part of the supply only shows up across the diode when it is in the reverse bias and blocked (acting like an open switch) there by making the output voltage zero at that instant.
Circuit diagram of half-wave rectifier?
It consists of four diode or rectifiers units with all cathodes (or arrows- schematically) pointing to the positive end DC ouput. All anodes point to the negative DC end and the AC voltage is applied to the remaining two junctions of diodes where cathodes meet anodes.
Why freewheeling diode is used?
1. Consider a simple half wave rectifier circuit consisting of an ac source a diode and a series R-L load.2. now during the positve half cycle of the source current, the diode conducts but it stops conducting when the negative half cycle starts.3. For an R-L load load current lags the source voltage and tries to flow in the previous direction even when the source voltage has reversed.4. This action due to the inductance, builds a high voltage across the diode which may exceed its forward breakdown limit and permanently damage it.5. Thus freewheeling diodes are used to short the load during negative half cycles and hence prevent the voltage breakdown of the semiconductor switches used in the control circuit.
What is the purpose of half wave rectifier?
it has only one diode
