If it is half the house, that implies the main breaker or the line coming in. Sometimes, double breakers will trip one of them and not the other. It looks like it is still on. Try flipping the breaker off and back on. If you feel comfortable doing it, open up the panel and check each breaker to see if current is getting through them. Just a two prong test light will tell you this. Start on the main, it may be that one of the lines coming in is dead. Looking at the question, you blew a fuse but the breaker does not show a blown fuse. You shouldn't have both in the same circuit. If you have screw in fuses there should be 2 large Buss fuses at the top of the panel. One of these could be blown. These have to be checked with a tester, there is no way to tell just by looking.
Assuming there is not a "power outage" to all houses in the area (otherwise known as a "power cut") then the answer is: Yes, the potential (voltage) is still in the overhead wires that lead to a house when the house electricity is only turned off at its own main switch inside the main breaker box.
If everything is working as it should then no current flows when the breaker is off. This is no better example of this than there is on answers. When a do it yourselfer looks for an answer and gets one, the answer is always ended with the suggestion that before doing any work always shut off the breaker. If the breaker is malfunctioning one symptom is that a voltage is still present even though the handle is in the off position. If this is the case change the breaker out immediately.
Turning the breaker on allows the power to flow through to the outlets, lights, and appliances on that circuit, so yes power goes to and through a turned on breaker. If the breaker is off, but the main power is on, power still get to the breaker, usually from the bus bar that runs down the middle of the back of the breaker box.
It's probably either a faulty circuit breaker or a faulty wire somewhere in the house. In either case you should contact a qualified electrician to solve the problem. If it's a wiring problem you could be risking a fire.
Either your breaker switch needs to be changed for a heavier one, the pool equipment needs to be put on an other circuit or better still one of its own.It is best to talk to an ellectrician about the delails involved.
Assuming there is not a "power outage" to all houses in the area (otherwise known as a "power cut") then the answer is: Yes, the potential (voltage) is still in the overhead wires that lead to a house when the house electricity is only turned off at its own main switch inside the main breaker box.
The term "blown engine" usaully means the the engine is dead in which case you would not have any power. In the racing world the term "blown engine" could mean something else. A blown engine would be an engine that is super charged with a blower in which case you would have more power.
If everything is working as it should then no current flows when the breaker is off. This is no better example of this than there is on answers. When a do it yourselfer looks for an answer and gets one, the answer is always ended with the suggestion that before doing any work always shut off the breaker. If the breaker is malfunctioning one symptom is that a voltage is still present even though the handle is in the off position. If this is the case change the breaker out immediately.
Turning the breaker on allows the power to flow through to the outlets, lights, and appliances on that circuit, so yes power goes to and through a turned on breaker. If the breaker is off, but the main power is on, power still get to the breaker, usually from the bus bar that runs down the middle of the back of the breaker box.
It's probably either a faulty circuit breaker or a faulty wire somewhere in the house. In either case you should contact a qualified electrician to solve the problem. If it's a wiring problem you could be risking a fire.
Check your breaker panel or fuse box, if they are not tripped or blown that's not the problem. If there has been a storm, look to see if power lines to your house are down. DO NOT GET NEAR THEM! If they are you need to call an electrician and the power company. If your power lines are OK, look and see if your neighbors have power. Look all around you because you and your neighbor next door may be on a separate circuit than the people across the street. If they have power you still need to call an electrician. If their power is out it is a general thing so be patient, call the power company and relax. You also need to find some candles and a flashlight for when it gets dark.
You would not be the first person to have someone else tap into your electric power. If you are in a detached house, it is fairly easy to find out. Turn off everything in the house. Leave the circuit breakers on. Have someone stand outside by the meter. See if the meter still runs. (You may need to turn off the breaker to the hot water.) If the meter is still running when nothing in the house is turned on, you can call the power company to come out and check.
Either your breaker switch needs to be changed for a heavier one, the pool equipment needs to be put on an other circuit or better still one of its own.It is best to talk to an ellectrician about the delails involved.
A breaker that still shows full voltage after it has tripped is definitely bad.
You need to remove everything connected to the breaker and see if it still trips. If it does it is in the wiring or possibly a bad breaker. Disconnect load from breaker and see if it still trips. If so replace the breaker. If it still trips and is not the breaker then you will have to start pulling each outlet from wall and checking after disconnecting each outlet.
If there is power to the aux connector and it still does not work, replace it with a new one.
If the GFI outlet is tripped (the outlet, not the breaker) then it is telling you there is a ground fault which must be fixed. If the GFI outlet is not tripped, and the breaker is not tripped, but it is still not providing power, then you have a loose connection or a wiring error.