0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you replace a valve cover gasket on a 89 Honda civic.?
TAke off valve cover then strip off old gasket.. clean entire serface with alcohol or gas or gasket remover. Then buy a new gasket from a local auto shop, along with some gasket sealer... Put on new gasket as old one was taken off. Use gasket sealer on top and bottom or gasket. Just a thin coat. THen place the cover back on with gasket in place and tighten bolts. Let sit for about 24 hours before starting to let the gasket sealer dry.. Should work better then ever.
Does steel seal gasket sealer gum up the engine?
Gasket sealers generally do now work on modern engines and should not be used.
Does a temporary head gasket sealer work on a 1978 Monte Carlo?
Not likely.... I'd never use anything "temporary" on a head gasket.
Does bard head gasket sealer really work?
IMO, this is only a temporary emergency fix. It will not permanently fix the problem. You will need a new head gasket.
What head gasket sealer do gm puts in there cars?
Barr's, tablet form. That's what I heard. The stuff does work well.
Does blue devil head gasket sealer really work?
yea it works good on a boat motor In my experience the only permanent repair for a blown head gasket is to replace it. These gasket sealers are only a temporary fix used in an emergency.
Do sealer head gasket repairs work?
MAYBEBut it is always a short term repair and it will cause other issues like plugged radiators and heater cores eventually.
Does head gasket sealer work?
It really should be looked as a very temporary repair more of a get you home type of fix Best if a faulty head gasket is changed have the head skimmed and pressure tested whilst it is off best wishes
Will concrete sealer work on asphalt?
My driveway has a ton of cracks in it, and I bought some concrete sealer, but my driveway is asphalt! Will the concrete sealer still work with asphalt?
Anti-freeze on spark plugs of your 98 ford contour SE 4cyl is this a blown head gasket Can this be fixed with a chemical sealer?
It is most likely a blown head gasket or a cracked head. Chemical sealers generally do not work. Your best bet is to replace the head gasket and inspect the head for damage.
When replaced the thermostat on a 1997 1.8 2WD Sidekick sport it leaks on the bottom screw of the housing if a thermostat sealer was used and it didn't work?
Two things I'd suspect are: First thing I'd suspect is that you missed a portion of the old gasket. These gaskets are some of the harder ones to remove as they are usually put on dry and actually penetrate into the pores of the metal(s). If you're not sure take the housing off and check to see if there's any old pieces of gasket left. If so, remove them with a good gasket scraper (I like the decal removers for this), pocket knife or sharpened putty knife. If you're sure the surfaces were clean then there are cautions if you used a gasket sealer. The gasket cements and solvent based sealers usually don't leak, silicones will if not installed properly. When using silicone sealers you have to let the sealer dry at least until it's almost completely set, if you don't the sealer can act like a lubricant and let the gasket slide which can cause a leak. I usually spread a thin coat on gasket, stick it to one of the metal surfaces and spread a thin coat on the other side of gasket. When the silicone is completely set I then install and the silicone will penetrate the pores of the metal which makes the gasket easier to remove.
How do you replace the oil pan gasket on a 1993 Buick Regal 3.1 engine?
Drain the engine oil. unbolt the pan and lower it as far as possible. If the pan is difficult to take completely out, see if you can reach around it to remove all of the old gasket and sealer. Carefully slide the new gasket in place, moving it inder the crank as you work it onto the pan. Add sealant, then rebolt the pan into place with the proper torque.
