0
In North America you can not obtain 230 volts from just one single pole breaker. The distribution is like this, from a one pole breaker to neutral is 120 volts. From an adjacent breaker to neutral is 120 volts. From the adjacent breaker to adjacent breaker (breakers situated beside each other) the voltage will be 230 volts.
If you want to incorporate a 120 to 230 volt transformer into the circuit you can obtain 230 volts. The primary side of the transformer will be connected to the 120 volt circuit and the secondary side of the transformer will output 230 volts. The transformer must be sized to the load amperage or the load wattage of the connected 230 volt load.
Wiki User
∙ 8y ago
Add your answer:
Earn +20 pts
What is the difference between single pole and double pole thermostats?
A line thermostat on a 240 volt heater must open both of the supply lines that feed the heater. This is where the double pole thermostat is used. On 120 volt heaters only one hot line needs to be opened to shut the supply off from the source therefore a single pole thermostat is used.
Can you use a 220 breaker in place of 110 breaker on 110 service?
Answer for USA, Canada and countries running a 60 Hz supply service.Breakers are rated in amperage and by the amount of poles that they have. Your classification of a 220 breaker is described in electrical terminology as a two pole breaker.Choosing the amperage of the two pole breaker depends upon the 220 volt load that it feeds.Two pole breakers for 220 volt loads.Single pole breakers for 120 volt loads.If the service is only 120 volt then every other bus bar in the panel will be energized. If the panel is a 120/240, then every bus bar in the panel will be energized.This is how and why a 240 volt load requires a two pole breaker.To the answer, yes you an use a two pole breaker in a 120 volt service but only one side of the breaker will have voltage on it depending on where it is situated in the panel board.
Panel box with a 3 pole 4 wire 440 volts 3 phase electric and you need to pull 220 volt single phase with 2 pole 3 wires how do you do it?
Open a discuss question page, more information is needed as to what you are trying to do.
How does a 20 amp double pole work?
Two pole what? Switch, breaker? 2 pole does just that. Either switches two separate sources like different legs of a 220 volt circuit or switches both the hot and neutral in a 120 volt circuit or plus and minus in a 12 volt circuit or a two pole breaker takes 2 separate 120v legs in a home breaker panel. Each leg of 120 volt breaker panel is 120 volts to ground and 240 volts between them. The electricity entering your house looks like a sine wave with each leg being 180 degrees out of phase from the other. The double pole breaker takes each separate leg to the device it is powering and provides 240 volts.
Can double pole circuit breakers be changed into single to create more room in the pannel box?
Yes. The double pole breaker can be removed and replaced with two single pole breakers. The double pole breakers are only used for 240 volt supply loads.
What is the Largest amperage single phase 120 volt breaker made?
6000amps <<>> The above answer must have big lugs to accommodate 6000 amp capacity wire. In my breaker catalogue the largest 120 volt single pole breaker is 70 amps, 277 volt single pole is 150 amps and 347 volt single pole is 100 amps. The 120 volt single pole breaker occupies two opposed slots because of its length.
What is the difference between single pole and double pole thermostats?
A line thermostat on a 240 volt heater must open both of the supply lines that feed the heater. This is where the double pole thermostat is used. On 120 volt heaters only one hot line needs to be opened to shut the supply off from the source therefore a single pole thermostat is used.
How do you know if your single pole is 240 or 120?
A single pole breaker will be 120 volts. But to make 100% sure test it with a volt meter.
Can you use a 220 breaker in place of 110 breaker on 110 service?
Answer for USA, Canada and countries running a 60 Hz supply service.Breakers are rated in amperage and by the amount of poles that they have. Your classification of a 220 breaker is described in electrical terminology as a two pole breaker.Choosing the amperage of the two pole breaker depends upon the 220 volt load that it feeds.Two pole breakers for 220 volt loads.Single pole breakers for 120 volt loads.If the service is only 120 volt then every other bus bar in the panel will be energized. If the panel is a 120/240, then every bus bar in the panel will be energized.This is how and why a 240 volt load requires a two pole breaker.To the answer, yes you an use a two pole breaker in a 120 volt service but only one side of the breaker will have voltage on it depending on where it is situated in the panel board.
Panel box with a 3 pole 4 wire 440 volts 3 phase electric and you need to pull 220 volt single phase with 2 pole 3 wires how do you do it?
Open a discuss question page, more information is needed as to what you are trying to do.
How does a 20 amp double pole work?
Two pole what? Switch, breaker? 2 pole does just that. Either switches two separate sources like different legs of a 220 volt circuit or switches both the hot and neutral in a 120 volt circuit or plus and minus in a 12 volt circuit or a two pole breaker takes 2 separate 120v legs in a home breaker panel. Each leg of 120 volt breaker panel is 120 volts to ground and 240 volts between them. The electricity entering your house looks like a sine wave with each leg being 180 degrees out of phase from the other. The double pole breaker takes each separate leg to the device it is powering and provides 240 volts.
Can double pole circuit breakers be changed into single to create more room in the pannel box?
Yes. The double pole breaker can be removed and replaced with two single pole breakers. The double pole breakers are only used for 240 volt supply loads.
How can I connect a single-phase - 2 hot wires plus ground- 220V load to a 3-pole 220V breaker?
Common usage of a three pole breaker is for use on a three phase distribution panel. Single phase distribution panels only use two pole breakers for a 240 volt load.Remember that the breaker must protect the conductors that connect to the load. If you want to try and use a three pole breaker in a single phase panel just because you have the breaker, this is not a good idea even if it will fit.Purchase the proper single phase two pole breaker to match the wire size and the amperage of the connected 240 volt load. Keep in mind that connected 240 volt motor loads have to be sized to 250% of the motor's full load amperage.By doing what you want to do and a fault occurs from this type of installation your insurance company might not cover the damage that it would cause.If the distribution panel is three phase then just connect the two load wires to any two of the three poles on the breaker.
Found 2 wires on a single circuit breaker why?
If it was two wires under one screw on a single-pole breaker, that would not be proper, and most probably against electrical code.If it was two wires, each under their own screw on a double-pole breaker, then that would be a 220 volt circuit; each wire going to its own "leg" of the breaker panel.
Can you use a double pole thermostat to replace a single pole thermostat?
Answer for USA, Canada and countries running a 60 Hz supply service.A double pole thermostat is a line thermostat and not to be confused with a low voltage stat. When the heating load has 240 volts for a supply voltage, both lines from the distribution panel are supposed to disconnect when the thermostat reaches the set point temperature. A single pole thermostat is only used on a 120 volt heater an the return leg from the heater is a neutral wire.A two pole thermostat can be used on a 120 volt circuit but a single pole thermostat should not be used on a 240 volt circuit. The reason being is that on a 240 volt circuit using a single pole thermostat, one "hot" leg doesn't get isolated from the heater and is always "hot" to ground. This is a shock hazard if you are working on the heater and depending on the thermostat as a disconnect from the distribution voltage.Before you do any work yourself,on electrical circuits, equipment or appliancesalways use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
How do you connect 230 Volt single phase to a 440 circuit panel?
You can't get 230 from a 440 panel. You'll need a step down trandormer
How do you upgrade household wiring from 110 volt to 220 volt?
your house has 220 you must use a 2 pole breaker. your wiring will change ,not a do it your selfer call someone
