0
Add your answer:
Earn +20 pts
How do you find the head bolt sequence for a Toyota Previa 2.4 1991?
start at top center and spiral your way around the bolt pattern clockwise tighten to 29 ft./lbs. then turn 90 degs once then twice done
What is the head bolt torque 1988 ford 3.9?
if alloy head 40nm then tighten 90 degrees
What is the torque sequence on a 98' S-10 2.2cylinder head?
Use the following sequence in order to tighten the cylinder head:Tighten bolt 1 to 63 Nm (46 ft. lbs.).Tighten bolt 2 to 58 Nm (43 ft. lbs.).Tighten bolt 3 to 58 Nm (43 ft. lbs.).Tighten bolt 4 to 63 Nm (46 ft. lbs.).Tighten bolt 5 to 63 Nm (46 ft. lbs.).Tighten bolt 6 to 58 Nm (43 ft. lbs.).Tighten bolt 7 to 58 Nm (43 ft. lbs.).Tighten bolt 8 to 63 Nm (46 ft. lbs.).Tighten bolt 9 to 63 Nm (46 ft. lbs.).Tighten bolt 10 to 58 Nm (43 ft. lbs.).Use J36660-A to tighten all the cylinder head bolts an additional 90 degrees in sequence
How do you use a wrench?
You fit the end over the bolt head and turn . - Clockwise to tighten.
Head bolt tightening sequence for Mazda e2000?
Begin by tightening the head bolts on each corner of the head. Next, tighten the center head bolts. Tighten the bolts on each end of the head and move towards the center.
What is head bolt tighting sequence for 2.2 Chevy 1994 model?
Always start from the center and work your way out. Kind of like in a circular motion but the circle gets bigger & bigger. # Tighten bolt 1 to 63 N·m (46 lb ft). # Tighten bolt 2 to 58 N·m (43 lb ft). # Tighten bolt 3 to 58 N·m (43 lb ft). # Tighten bolt 4 to 63 N·m (46 lb ft). # Tighten bolt 5 to 63 N·m (46 lb ft). # Tighten bolt 6 to 58 N·m (43 lb ft). # Tighten bolt 7 to 58 N·m (43 lb ft). # Tighten bolt 8 to 63 N·m (46 lb ft). # Tighten bolt 9 to 63 N·m (46 lb ft). # Tighten bolt 10 (stud bolt) to 58 N·m (43 lb ft).
What is the head bolt torque for a 1994 Pontiac 2.0?
CAUTIONTo prevent cylinder head damage, GM recommends the usage of a Remove Cylinder Head Bolt Sequence with a cold engine. For installation, always use NEW cylinder head bolts. TORQUE SPECIFICATIONS:Cylinder Head/Camshaft Carrier Bolt 2.0L:Step 1: Torque all bolts to 18 Ft.Lbs. (24 N.m)Step 2: Tighten 60 DegreesStep 3: Tighten 60 DegreesStep 4: Tighten 60 DegreesStep 5: Tighten 30-50 Degrees
What is the Head bolt torque sequence 1981 Honda cb650?
Tighten the head bolts in 2-3 steps to a final 30 NM
What is the 4G13 P SOHC cylinder head bolt torque specs?
Tighten the bolt in the sequence until each is torqued to 49 Nm, then completely loosen all the bolt then re-tighten them in sequence once again until each torqued 20 Nm. tighten each bolt again by 90 degree in accordance with the tightening sequence. After that tighten each bolt again by 90 degree in accordance with the tightening sequence. Some mechanics will refer this method as "20+90deg+90deg"
What is the head bolt tensions on a V6 VT Commodore?
1. Tighten head bolts in sequence to 34Nm/25lbft.2. Turn each bolt 90 degrees.3.Tighten to 90Nm/67lbft.If while turning through 90 degrees 90Nm/67lbft is reached stop tightening that bolt.NEW HEAD BOLTS must be used.
Honda d15b2 head Tightening Sequence?
The Honda had bolt tightening sequence begins with the head bolts on each end of the head. Tighten the head bolts moving to the center, alternating from and to end.
What are the head bolt torque specs for a Cat 3024?
The head bolt torque specifications, for a Caterpillar 3024 diesel engine, is 170 pounds per square inch. The bolts should be tighten at 50 pound intervals.
