0
Yes, usually I like to start it with some copper (8 inches) and then attach pex adapters. You can run it directly to it, but it's awkward you're crimping on pex to brass fittings on the tank, it's hard to crimp. If you can manage it, there's nothing wrong with it. It's easier to add a copper nipple first.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
You received an electrical shock by your showerhead.?
Grounding may be an issue. Have you replaced any coper pipe with plastic, polly or PEX pipe of any kind? if so you will need to add a bonding jumper at the beginningto theend of the plastick pipe. If not, first check to see if there is a ground wire at the water service main entrance. Next see if it is continouse past all couplers and valves and conected to the other side,including the PRV. Also check to see if there is a bonding (grounding) wire at the water heater from the cold to the hot side of the water heater. Hope this helps Terry
What does PEX stands for in DU results?
PEX is produced with crosslinked polyethylene. Crosslinking is obtained through a chemical process that increases the bonds between macromolecules to form a more complex structure than the normal polyethylene. Due to the crosslinking, the polyethylene's performance is greatly enhanced still maintaining the excellent properties of thermoplastics. for more details you may visit on this link : http://www.ardipex.com/pex-pipes.php
What is the flow rate of water through .75 inch pex pipe at 40 psi in gpm?
The standard formula to calculate flow(GPM - gallons per minute) from a CIRCULAR orifice is:29.7 * (the square root of the pressure) * (the square of the diameter of the flow orifice)EXAMPLE using 3/4" Pex Pipe(actual I.D. of 3/4 PEX Pipe is .677") and 40 PSI pressure:29.7 * 6.325(sq. root of 40) * .458(the square of the I.D. 3/4" pipe) =A GPM of 86.03Note: You also need to account for fittings in the loss calculations; while minimal several fitting will make a difference.
Do I have to insulate pex tubing in below freezing climates?
It may depend on whether or not your pex plumbing is underground (as in a house) or exposed to the subzero air (as in a trailer home). Underground the earth acts as an insulator. Snow piled up against the skirting of a trailer is a very effective insulator. Unfortunately, you can have subzero temperatures without snow, so I would recommend insulation or heat tape in exposed pipes. You may also consider installing a heat source, like a ceramic heater, if you have a trailer. And of course, leave your taps dripping just in case! I have found pex plumbing to be worth the extra cost because although my pipes froze at 20 degrees below, they did not burst. By Linda: I would like to correct a couple remarks above: 1. In underground installations, PEX needs to be installed below the ground freezing level, no matter what the application is. 2. If the tubing is against the exposed wall, the answer is yes, always. You can use split type closed cell foam insulation for such purposes, same as the one used by HVAC contractors.
A synthesis organizer is a place to what?
write down the major points in an article. =]
Can you connect PEX to a water heater?
No. Not directly. It needs to be 18 inches away... in length, not distance according to the UPC. An 18 inch water heater flex would work or 18 inches of copper tube with a pex adapter on the end will work.
How does PEX supply tubing get connect to city water meter?
for a 3/4" supply use a 3/4" PEX x 3/4" NPT Brass F Adapter
What is the best type of material for water pipe replacement?
PEX is by far the best, long lasting and easy to connect .
How do you connect PVC water line to pex plumbing?
There is a product that is sold at Home improvement stores called "SharkBite". It will allow you to connect Copper,CTS Cpvc and Pex. Here is the link to learn more. Your friend, Matt The Handyman http://www.cashacme.com/prod_literature.php
Can pex be used for hot water?
Pex is very resistant to extreme temperatures and can be used for hot water.
Where can one find Water Heater dealers?
There are many places where someone can find water heater dealers. There are many companies online where someone can easily find a water heater dealer. Also, ads in the newspaper can have information on water heater dealers in a persons area.
What is torrent peer exchange?
Peer Exchange (PEX) allows you to connect to new peers through a peer you are already connected to. Ordinarily peers connect to each other through trackers. PEX allows them to connect without a tracker, by communicating with each other.
Will Goop glue PEX PIping?
Goop will appear to glue PEX piping, but will separate as soon as water pressure is applied. -The only way to join PEX properly is a PEX coupling, or a Sharkbite.
Is it okay to use three-eighths PEX pipe for a tankless water heater manifold system?
It depends on the length of the run. 3/8 pipe tends to be a little small and will restrict the flow. Use the 1/2 if you can. It's not that much extra but it will give you much better water delivery. Of course, between the manifold and the water heater, use 3/4 inch or larger copper. ___________________ I would have to agree with the previous contributor. 1/2" PEX is indeed the preferred size for running the water to the plumbing fixtures.
Can pex water tubing be used underground?
YES!
Why would there be no hot water in a shower faucet that is not used very ofter?
If galvanized piping was uset to plum the house, it may have rusted shut, an easy fix would be to run a new line in copper or PEX from the water heater to the valve
What are the costs of Bradford White water heaters?
The price of Bradford White water heater starts from $499. They can be purchased from the following sources: Pex Supply, Bradford White, Price Grabber, Nextag, Amazon, Consumers Plumbing, to name a few.
