Different plugs are designed so that you can't plug an appliance into the wrong voltage. A dryer is usually 220-240 Volts and your standard outlet is 110-120 Volts. You can't do what you suggest.
Yes you can... have one and plugged into regular wall plug (110v) in USA.
Hard wired means that there is no plug and receptacle in the circuit powering the dryer. What you will find is a metal jacketed cable that will come out of the wall or floor and go right into the dryer.
Usually a stackable washer and dryer system will need a special outlet. Dryers usually run on a 220 outlet so they will need a special outlet installed where you plan to place your washer and dryer.
It's probably more difficult than you might expect. I'm assuming you have a NEMA 5-15R outlet, and you want to plug in a dryer that has a NEMA 14-30P plug at the end of its electric cable. The NEMA 5-15R outlet is by far the most common type of outlet in North America. It has two flat slots (hot and neutral), and a round safety ground hole. It is rated for 15 A and 125 V. On the other hand, most electric clothes dryers have an electric cable with a NEMA 14-30P plug on the end. It has two flat slots (2 hots from 2 different phases, each one 120 V from neutral, and each one rated at 30 A), an L slot (neutral), and a round safety plug. It is possible for an electrician to "fish" a electric cable carrying the necessary phases through the wall from the fuse box to that outlet, and then pull the old outlet and install a new outlet. If one merely did that last part -- pulled the old outlet and placed a new outlet -- without the proper electrical cables in the wall behind it, then the dryer would probably blow the fuse at the fusebox every time it was turned on.
plug them into the wall
Yes you can... have one and plugged into regular wall plug (110v) in USA.
Hard wired means that there is no plug and receptacle in the circuit powering the dryer. What you will find is a metal jacketed cable that will come out of the wall or floor and go right into the dryer.
Usually a stackable washer and dryer system will need a special outlet. Dryers usually run on a 220 outlet so they will need a special outlet installed where you plan to place your washer and dryer.
If you mean installing a plug in your wall for the dryer, I advise calling an electrician unless you know someone who is very experienced and confident with electricity. A dryer requires 220 volts of electricity, twice what most home outlets deliver. A line has to be run from each side of your breaker box through the wall to the where you want the outlet to be (110 volts from each side of your breaker box). If you go to a large home/hardware store, they can show you the right plug to use. Again, electricity is very dangerous, especially when you are working directly with the service panel (breaker box) in your house. Please be safe.
No. Normally they can go right against the wall unless anything in its manual prohibits it.
You can find a leak behind the wall by removing a portion of the wall.
The best hand dryer model that would be the best for mounting onto a marble wall would have to be the Exlerator Hand Dryer . It is more eco friendly and it has enough strength to be mounted on virtually any type of wall .
Under the new electrical code rules three prong dryer cord receptacles and therefore cords are not allowed to be installed. As you are finding out, stores are not carrying them in stock any more. You should consider an upgrade for safety sakes, to a four prong plug cord and change the wall receptacle to a four prong receptacle. There are instructions on how to do this your self on Answers.
the map sensor should be on the right fender well or right fire wall it has one wire plug and one vacume plug
If you only have one wall socket where the washing machine and dishwasher are, then you could plug in a multi-plug adaptor, into which both appliances could then be plugged in. There are also multi sockets in a strip with a single plug on a short cable available. For instance, in my outhouse, I have a dryer and a washing machine that are plugged into a three way adaptor. The adaptor is then plugged into a RCD, or residual current device. Finally, the RCD is plugged into the single wall socket.
While the Xbox is turned off, plug the power supply into the xbox first. Then plug it into the wall and it should be orange. Turn on the xbox and then the light will change to green.
If it has a plug, insert the plug into a wall socket. Some have AC adapters - make sure the adapter is connected to the tree, then plug the adapter into the wall socket...