0
No. If you have phase 1, 2, 3 (in that order), and phase 1 is the highest voltage at the instant a switching event occurs (causing a power surge), the surge voltage will be highest in phase 1. For polarity to change, you would need phase 2 to instantaneously change to greater than 1, which will not happen.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
Can small permanent magnet motors be reverse direction if the direction of current flow to the motor is reverse?
Permanent magnet field motors. With a these motors, a permanent magnet is used to replace the field coil. DC power is connected via the brushes, to the armature only. Reversing the polarity, will cause the motor to reverse its direction of rotation. It is very common to use a switch to intentionally reverse to the polarity, to allow reversal of the motor if desired.
What happens if the direction of current at the terminals of a series motor is reversed?
No changes will occur by wiring a 110 volt motor in reverse polarity, rotation will always be the same. Some single phase motors are designed to be reversed ,but that is a function of the relationship of start windings and capacitors and requires some wiring changes in a motor junction box or an end terminal housing, not by just changing the incoming power.
Why did your band saw motor reverse direction?
the power leads were wired wrong
How do maglev trains slow down?
You slowly decrease the power of the electromagnets.
Will running a motor backwards generate power?
No. Motors can be run in either direction, clockwise or counter clockwise. However, mechanically spinning an electric motor will generate electric power.
Can small permanent magnet motors be reverse direction if the direction of current flow to the motor is reverse?
Permanent magnet field motors. With a these motors, a permanent magnet is used to replace the field coil. DC power is connected via the brushes, to the armature only. Reversing the polarity, will cause the motor to reverse its direction of rotation. It is very common to use a switch to intentionally reverse to the polarity, to allow reversal of the motor if desired.
What would cause a 12 volt motor to change polairity?
This assumes you have a 12 volt direct motor. You should be able to simply reverse the wires leading to the terminals. There should be two wires going to the motor. Change them around.
Would reverse polarity cause equipment to run even if switch is off?
The case of reverse polarity would only happen on a DC system. As to would it cause equipment to run when switched off, no, if the switch opens the equipment's power supply completely the device will not operate.
What happens if the direction of current at the terminals of a series motor is reversed?
No changes will occur by wiring a 110 volt motor in reverse polarity, rotation will always be the same. Some single phase motors are designed to be reversed ,but that is a function of the relationship of start windings and capacitors and requires some wiring changes in a motor junction box or an end terminal housing, not by just changing the incoming power.
How do you test reverse power trip?
There is a test swich which will change the polarity of the sensors........
What would cause a table saw motor to reverse itself while running?
if the power wires for the motor happen to be hooked up backwords
Is polarity important when using power tools?
Only if it is a battery power tool and you fit the battery in reverse.
Differentiate between the terms reversed polarity and normal polarity?
Normal polarity is for the power to normally go from positive to negative, reverse polartity is to change the positive to a negative and the negative to a positive so the power goes the other way.
What is an example of reverse polarity?
Reverse polarity means connecting a power source, or polarised componenet, with the positive and negative poles the wrong way round. If the positive and negative supply is connected the wrong way round in electronic devices, it usually causes damage, because semiconductors are sensitive to polarity. Sometimes protection is provided, so that reverse polarity stops the device from working without causing damage. Connecting a diode (or rectifier) in reverse, will block the flow of current, without causing damage and is useful in protecting circuits from reverse polarity. In some consumer electronics (especially CB Radios) the power input has a recitifier across the 12v supply. If it is wired correctly, the rectifier is in reverse polarity, does not conduct and allows the radio to work. If you reverse the polarity of the power supply, the rectifier is now in full conduction, across the supply, causing a dead short. This shunts any power away from the radio and blows the fuse in the line, thus protecting it.
How stepper motor started?
A: A stepper motor does it not start and spins but rather move to the next position according to the polarity of the power applied
Left side electric mirrow works right side does not motor or switch 2004 Columbia freightliner?
Requires further diagnosis. You'll have take out the interior door panel and test the connection at the motor to see if power is getting to it. With the switch not engaged, there'll be no power. With the switch engaged, there'll be power, but the polarity for up is reverse from when the switch is in the down position.
What are the effects of reverse polarization in electronics?
When a magnet's polarity is reversed, the changing magnetic lines of force cutting across wiring induces a voltage in them. This principle is used primarily in motors. Or perhaps this refers to applying DC power to a device in reverse polarity by mistake. If the device is well designed, it will have a safety diode in the power input area to prevent damage, but if the diode is not present, reversing the power polarity will probably destroy every semiconductor junction in it.
