0
I got a call back from my local dealer and Intake manifold bolts are 115 in./lbs and rocker arm bolts are 14 ft/lbs then 30 degrees past that. Also good to point out that push rods are long on outside of gasket, short on inside of gasket closest to the head.
Wiki User
∙ 16y ago
Wiki User
∙ 16y agoSmall block Chevys have adjustable rocker arms, so there is no torque spec for that. Rockers are adjusted for a specific backlash and/or preload based on the type of cam being used. Refer to cam card or auto repair manual for your application.
Wiki User
∙ 13y agoThe torque for roller rockers should be 25ft lbs. It was perfect for my 3.4l. It ran very smooth and quiet.
The correct torque for the rocker arm bolts is 124 inch pounds plus 30 degrees.....
25ft ponds would bind you up pretty bad I'm surprised the engine turned This is some what correct...... The answer is correct at 124 inch pounds + 30 degrees. As this is done you will end up at about 20 foot pounds. Lets start from the beginning. 124 inch pounds is 10.3 foot pounds, so if you start at 10ft and turn the bolt head a bit less than a quarter turn you will end up at about 20 to 21 foot pounds. I am not saying the torque spec is not important. But the other author said the 25 ft lb will bind the motor up. This is not true. The rocker is a non adjustable pedestal type. So this means tight is tight. If you make some tighter than others it will not change the clearance. These are auto adjusting zero lash rocker and cam and lifters. Tighter or looser only changes the torque spec, nothing else. The factory spec is there for a reason, please use it. 124 inch pounds + 30 degrees.If you only have a ft lb torque wrench the conversion is to divide 124 by 12. You end up with 10.3. As far as turning the bolt 30 dg, think of a clock. Hand on twelve and turn to the two. This is 30 degrees.....
Wiki User
∙ 14y ago14ft lbs.
Add your answer:
Earn +20 pts
Rocker arm specifications for a 1994 3400 sfi?
what are the torque specs on a 3.4 s.f.i
What are the 2004 Pontiac Montana lug nut specs?
100 Ft. lbs.
What are the Torque specs on 1997 Pontiac GTP supercharger?
If you mean engine performance, then it has 240 hp and 280 lbs of torque
Torque specs for 5.0 GM rocker arms?
All of the torque specifications for vehicles can be found in Haynes Repair Manuals available at most auto parts stores.
What are the torgue specs on rocker arms on a 2001 malibu 3100?
All of the torque specifications for vehicles can be found in Haynes Repair Manuals available at most auto parts stores.
What is the intake manifold torque specs and ordering for the 3.4L on a 2001 Pontiac Grand Am?
need torque specs for 3.4 pontiac grand am intake and rocker arms
Rocker arm torque specs for 1997 Pontiac Transport 3400?
The 1997 Pontiac Transport 3400 rocker arm torque specifications are 18 pounds. The rocker arm should be torqued in six pound intervals.
Torque specs for 97 Pontiac grand am 3.1 rocker bolts?
18 ft pounds
What are the torque specs for 1970 Pontiac 400 Ram Air engine rocker ams?
20 foot pounds.
Torque specs Chevy 2.2l rocker arms?
what is the torque on 2.2 rocker arms and in what order
Rocker arm torque specs?
what is torque spec for rocker arms on 2004 4.6 landrover discovery
What is the torque spec for a 2003 Aztec?
rocker arm torque specs
Do you have the rocker arm Torque specs for a 1998 Pontiac 3400?
14 ft pounds plus 30 degrees torque to 14 ft lb then turn 30 degrees more
What is the rocker arm torque specs 1999 Ford Ranger 3.0?
i'm looking for the torque specs on the rocker arms on a 1999 ford ranger 3.0 v6 the torque is 18-26 lbs
What are the specs for the rocker arms on a 3.1 sfi?
The rocker arm specs for a 3.1 sfi is 18 foot pounds of torque for the rocker arm nut. The nut should be set with a torque wrench as this setting needs to be accurate.
What are the torque specs for the Rocker arms on a 3100 V6?
14lbs
Where can you find the torque specs ona cat 3176 engine rocker arms?
i need rocker arm torque for 3176 cat
