answersLogoWhite

0


Best Answer

Its up underneath the dash. There are four bolts and three wires, black, red and orange and you are done.

the first answer is from someone who has very obviosly never even seen a nova ignition switch. if you have the key, simply put the key in the ignition and leave it in the off position. take a paper clip and insert it into the small hole next to the key, this will allow you to push the switch in further and twist the key counterclockwise allowing the whole unit to slide out.

if you don't have the key, good luck. its a nightmare.

Actually, I think you need to insert the paper clip while the key is in the "accessory" position, then push in and turn counterclockwise. The cylinder can be removed at this point, and you can then remove the bezel nut that holds the ignition switch in place.

both of these answers are telling you how to remove the lock cylinder. the ignition box or switch "both names are commonly used," is on the top of the steering column under the dash. there are two bolts and a wiring harness attached to ignition box. simply remove the two bolts and unplug the wires, remove and reinstall. the hardest part is adjusting the box so the actuator bar is pushing switch into proper position. if you are talking about the lock cylinder go with one of the obove answers. Wow. When the key is on the column, is when they went to the rod type system. On that Nova, it is on the dash, attached to the lock, and tumbler. One piece. the third answer, is the most accurate.

User Avatar

Wiki User

8y ago
This answer is:
User Avatar
More answers
User Avatar

Wiki User

8y ago

If you want to change the SWITCH, it is on the steering column about 18 inches above the floor. If you want to change the lock cylinder you need to remove the steering wheel, then the lock plate then the turn signal switch then the key reminder switch {the two little copper contacts} and you will see a screw that has a different head that goes through the edge of the cylinder. Take the screw out then pull the lock cylinder out.

This answer is:
User Avatar

User Avatar

Wiki User

15y ago

turn the bezel nut off the ignition switch, then insert the ignition key into the ignition and get yourself a paper clip and put one end of the paper clip into the small hole next to the key and push in and turn the key to the left and the ignition lock will pull out, then you need to reach under the dash and pull the whole switch out and take all the plug-ins off of it and get your new switch and put the plug-ins back on and reinstall the switch through the dash then take your key and ignition lock and reinstall by basically putting it in the same position it came out and twisting the key like your starting it and it will lock back in, next take the key out and put your bezel nut back on and tighten it and your done.

This answer is:
User Avatar

User Avatar

Wiki User

12y ago

You should buy a Haynes manual for the car but this is how I did it with the manuals help.

Pre Start: Remove Negative Cable from Battery and/or disable airbag.

1) Pull the kick-panel from the driver side under dash.

2) Remove the 4 small bolts holding the brace for the Steering Column.

3) Remove the 2 Large bolts that hold up the Steering Column and drop the column down. (You may want to remove one of the screws that hold the column to the firewall area, although I did not have to do that)

4) The ignition switch is located right on top of the column. Remove the Two bolts that hold the switch to the column and pull the switch up and off of the linkage.

5) Remove the bolt that holds the connector block in place at the other end of the wires.

6) Remove the two outside connectors by inserting a small screwdriver in between the Ignition switch and the outside connector to release it.

5) The park cable can be detached by removing the two very small black Phillips head screws holding it to the switch.

This answer is:
User Avatar

User Avatar

Wiki User

10y ago

The ignition switch lives on top of the steering column under the dash board.

It is normally retained by two or three screws depending and may have two separate wiring plugs.

Its a pain to change but not a big deal.

This answer is:
User Avatar

User Avatar

Wiki User

14y ago

Are you asking about the key cylinder or the actual electric switch?

This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you replace the ignition switch on a 1986 Chevrolet Celebrity?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you replace an ignition switch for a 1977 Chevrolet truck?

n ignition switch on a 1991 Chevrolet astro vanAnswern ignition switch on a 1991 Chevrolet astro van


How do you replace a 95 Chevrolet pu ignition switch?

very carefully


How do you replace the ignition switch in a 79' Chevy Scottsdale?

Retaining ring from the top of your 1979 Chevrolet Scottsdale ignition switch. Slide the switch out and remove the wiring harness. Reverse the process to install the new ignition switch.


How do you install an ignition switch on a 1986 Chevrolet caprice?

Attach the wiring harness to the and of your 1986 Chevrolet Caprice ignition switch. Slide the ignition switch into the ignition slot. Tighten the ignition switch with the retaining ring.


How do you replace the ignition actuator or rack on a 1995 Chevy astro?

what is an ignition actuator i work on Chevrolet and have never heard of it are you talking about the switch


How do you replace an ignition switch in a 99 suburban?

how DO YOU REMOVE AN IGNITION CYLINDER FROM A MALIBU CHEVROLET 2000


How do you replace the ignition switch on your 1993 Chevy K 2500?

Remove the retaining ring at the top of your 1993 Chevrolet K 2500 ignition switch. Slide the ignition switch out and remove the wiring harness. Reverse the process to install the new ignition switch.


How do you replace an ignition switch on a 2001 Monte Carlo ss 3.8?

Begin by removing the retaining ring at the top of your 2001 Chevrolet Monte Carlo ignition switch. The ignition switch barrel will slide out. Remove the wiring harness from the end of the ignition switch. Reverse the process to install your new ignition switch.


How do change the ignition switch on 95 Chevrolet g20 van?

You can change your 1995 Chevrolet ignition switch by removing the ring at the top of the ignition switch. Slide the ignition switch out and remove the wiring harness. Reverse the process to install the new ignition switch.


How do you replace the key cylinder ignition on a 1979 El Camino?

You will need to remove the retaining ring at the top of your 1979 Chevrolet El Camino ignition switch. The ignition switch will slide out. Remove the wiring harness. Reverse the process to install the new ignition switch.


How do you replace ignition switch with no keys?

You do not need a key to replace the ignition switch.


If the ignition switch locked up on a 2000 Chevy Impala how do you get it to unlock or reset?

I'm told this is a common problem that Chevrolet is aware of. Contact your local dealer. They should be able to replace the ignition switch and charge it back to Chevrolet as a warranty repair.