0
I have the same problem, going to have a locksmith make sure its the ignition switch and cylinder and just not a key problem or a tumbler problem.
Wiki User
∙ 8y ago
Wiki User
∙ 17y agothe library should have a shop manual for this vehicle, you can make copies of the right sections :)
Wiki User
∙ 13y agoI have a 1995 T100 and need the answer to this question as well. Anyone have any answers. I can't even get it started to take it in for service. I need help. Thanks
Wiki User
∙ 15y agoHOW DO I REPLACE 1998 camry ignition switch?
Add your answer:
Earn +20 pts
Your 1985 Toyota pickup turns over but won't start has no fire from coil wire?
first i would check your coil, if its good, check your ignition switch.
When you push in your brakes on my 91 Toyota 4Runner why does the dashlights come on?
Check the brake light bulbs, one of them may not be installed correctly.
Car won't start with key switch but will if you jumper over solenoid on starter?
Check the neutral safety switch,it is located on the transmission or on the steering column ,under the dash.
Why does a 1996 Ford Ranger XLT 4.0L start when you cross the posts on its solenoid but not when you turn the key in the ignition?
the solenoid itself is probably bad, if not that probably the ignition switch I agree 100%, check the solenoid first then the switch.
Key turns will not start it is like the safety switch on the clutch is not engageing any suggestions?
several could bes. If there is no action, the engine does not turn, the rod running from the key switch to the ignition switch on the column could be broken, or the ignition switch itself could haved malfunctioned. If there has be work immediately privious to the problem, check for loose connection, expecially on the ignition switch.
Key can't be removed from ignition on a 1997 Toyota 4runner. what's the fix?
Most likely its an Ignition Switch/Cylinder issue unless you know that you have an alarm system that has the ability to lock the ignition switch. Other issues is that it could also be the Tumbler. If its stuck, best bet is to either call a locksmith and have them check it out, or have it towed to a garage that you trust.
1999 4runner will not turn off even when key is out of ignition help?
Check all the wire coming out of the ignition switch, make sure that theres no bare wire or shortage between them or to the body..If wires are ok, your ignition switch needs to be replaced.. the switch doesn't turn with the cylinder..
99 Toyota 4Runner fog light where is the switch?
Switch or relay? The switch is in the dash to the left of the steering wheel. The relay is in the fuse box out in the engine compartment, check the lid of the fuse box to determine the relay location within the box.
Your 1985 Toyota pickup turns over but won't start has no fire from coil wire?
first i would check your coil, if its good, check your ignition switch.
HowtoReset maintenance light 2005 Toyota 4Runner?
Check your maintenance manual. It's in there.
How do you reset the check engine light for a Toyota 4runner?
have you tried pulling the EFI fuse
What do you do if the check engine light comes on in a 1997 Toyota 4Runner and stays on?
go to auto zone and have them check it for you. its free
How do you reset check engine light on 2003 Toyota 4 Runner?
Type your answer here... Hello how do you reset the check engine light on a 2003 Toyota 4runner. Thanks
Why does the check engine sign come in Toyota 4Runner?
Because the ECU has detected a problem with the emissions system.
Where is the automatic transmission fluid filler on a 1997 Toyota 4runner?
Same place you check the fluid level.
Why does the keys on a 1997 Toyota Camry LE only come out of ignition when the battery is disconnected?
I would check the transmission safety switch. If it's faulty you will not be able to get your key out.
After oil change the check engine light came on in the Toyota highlander?
I was able to reset by holding odometer button down while turning off ignition switch and turning ignition switch to on and watching dashing go from 5 to 0 and the maintenace odometer resetting to zero.
