The year, make and engine info would help.
sine wave
oil light comes on when there is not poper amount of oil in engine. if proper amount is in engine and light comes on at idle, maybe the oil needs changing. oil looses some of its viscosity when old/you might also check oil sender unit and oil pressure gauge. it all these are good you need new oil pump,as it is loosing pressure at idle. just because oil light comes on , DOES NOT mean you need new main bearings. YOU WILL KNOW WHEN U NEED MAINS AS THE ENGINE WILL RATTLE LIKE A THOUSAND LITTLE MEN IN IN WITH HAMMERS. THIS NOISE WILL ALSO GET WORSE WHEN YOU REV ENGINE
It really depends on where you are going to use the bulbs!All the light bulbs do not operate the same voltage for starters, there would be nothing surprising about that, but unless you are aware of the differences between them you could be in a little shock. LED bulbs come in two primary voltages: mains voltage and low voltage.Mains Voltage BulbsThe mains electricity supply in the United Kingdom is 230 V Ac (Alternating Current). This is used to supply the majority of domestic and commercial lighting.LED (Light Emitting Diodes) operate at low voltage DC (Direct Current). As such, LED bulbs that are designed to run straight off the mains, like GU10, B22 or E27, require a driver to change the voltage from 230 AC.You will observe about GU10 LED bulbs (230 V) is that they are slightly longer than the low voltage MR16 bulbs(12 V). This is due to the fact that the driver unit is placed into the GU10 fitting.Low Voltage BulbsLow voltage bulbs, are simply lights that run at a lower voltage than provided by the mains electricity supply. They used to exist in the cars where connecting to the mains electricity supply was not viable and the lights would have to run off either a 12V or 24V engine battery instead.Low voltage lighting in houses is a recent innovation. It is created primarily for fittings in kitchens and bathrooms. Instead of being connected directly to the mains supply, an intervening transformer 'steps down' the mains voltage.When you exchange your old halogen bulbs for MR16 LED, there is no guarantee that they will work with your existing 12 V transformer. Contact your retailer to determine whether or not you need to upgrade your system.LED lights have come a long way in the last few years and so have the prices so keep looking. Any good LED lighting website will have info on which lights are best for the application you need them for so have a look around.
Lack of oil or incorrect oil. A tired oil pump A plugged up oil sump screen. Worn out bearings (cam, mains and rods) An incorrect reading from the oil sending unit or gauge.
Landslides or slips in urban areas, almost always have a source of water as their cause. Broken water or sewage mains are often to blame.They occur where the ground has been inadequately consolidated, as in a subdivision of land; or where the land is steeper than its natural rest angle.Rainfall in storm conditions will often saturate the soil structure, exacerbating the problem.
What is the mains and big end bearings torque setting for uno 1100 engine
Need to know what year and engine size.
the big end bearings torque down at 55 - 65 Nm
Heads Torque at 65 Ft. Lbs. Mains Torque at 70 FT. Lbs.
Mains 85------- rods 45
The head bolts on an Isuzu 4JB1 engine are usually rated at 57-67 foot-pounds new. The rods are rated at about 58-65 foot-pounds, and the mains are rated between 116-130 foot-pounds.
torque settings for mains,big ends and cylinder head Opel Corsa 1.7diesel 2000
Torque Settings Mains = 108NMBig Ends = 54NM + 90° +90°Flywheel = 122.5NMCylinder Head = 78 NM + 90° + 90°Valve SettingsExhaust = 0.40 mm - 0.50 mmIntake = 0.20 - 0.3 0mm
mains are 70 ft lbs plus 90 degrees
mains 80 ft lbs rods 33 ft lbs main support brace 35 ft lbs
To make a cool design on stardoll, simply select the pieces of the outfit one likes. From there, place them in a way that one feels the outfit's design seems "cool".
65 FT. LBS.