answersLogoWhite

0


Best Answer

I know that you have to put the truck in base timing mode for my 93' but I have a EST or HEI style ignition. If you have the electronic distributor then find the grey wire with a plug on the end of it next to the A/C box on the left side under the hood near the firewall. It will be hanging out of the wire harness. Apply 12 volts to it from your battery with a jumper wire and the truck will go into base timing mode. then line up the marks on your balancer. take the jumper wire out and your set.

User Avatar

Wiki User

โˆ™ 2007-12-24 17:36:32
This answer is:
User Avatar
Study guides

Where I can purchase purchase HID Fargo ID card in Dubai

โžก๏ธ
See all cards
3.33
โ˜†โ˜…โ˜†โ˜…โ˜†โ˜…โ˜†โ˜…โ˜†โ˜…
3 Reviews

Add your answer:

Earn +20 pts
Q: What is Ignition timing procedure for a 1992 Chevy s10 2.8L v6?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

What is the ignition timing spec for a 1992 Chevy Camaro with 305?

6 BTDC


Where is camshaft pulley ignition timing location for 1992 Toyota Corolla?

where is camshalf pulley ignition timing location for 1992 Toyota corolla?


What is the ignition timing spec for a 1992 Chevy K1500 pickup with 4.3 liter engine?

advance your timing 6 degrees due to this ethanol crap fuel we run now


How much time on average is to replace the timing chain on a 1992 Chevy Corsica?

It will take an experience mechanic approximately 8 hours to replace the timing belt in your 1992 Chevy Corsica. The 1992 Chevy Corsica does not have each timing chain, it has a timing belt.


How Do You Replace Ignition In 1992 Cavalier?

how do you replace ignition switch on a 1992 Chevy cavalier 2.2 4 cylinder


Does a 1992 Chevy truck have a timing chain or belt?

it has a timing chain NEUTZ


Where are the timing marks located on 1992 Saturn?

No need for timing marks on the outside of the engine that has no adjustable ignition timing.(DIS)


How do you change the ignition switch on a 1992 g20 Chevy van?

Begin by removing the retaining ring at the top of your 1992 Chevy ignition switch. The ignition switch will slide out. Remove the wiring harness from the end of the ignition switch. Reverse the process to install the new ignition switch.


Where is the Ignition Module located in a 1992 Chevy Corsica?

The 1992 Chevrolet Corsica ignition module can be found on the firewall in the engine compartment. The ignition module will be on the drivers side of the firewall.


How much does it cost to replace the timing belt on a 1992 Chevy Lumina?

$ 5,000


What is the ignition timing spec for a 1992 Chevy K1500 Blazer with 5.7 liter engine?

I have a 1994 5.7 k1500, and my book says for V8 5.7 1988-1995 is TDC. (top dead center)


How do you set the timing on a 1992 b2200?

The full procedure is a bit lengthy to write out so I've attached some links below to show you how. To adjust your ignition timing loosen the 12mm bolt in the middle of the distributor slide and move the distributor towards the front of the truck to advance the timing, move it towards the back of the truck to retard the timing.

People also asked

How fast can you run lipids into a peripheral line?

View results

What is prostate cancer and how is it caused?

View results

Is cumin seeds monocot or dicot?

View results

Does the humidity affect the popcorn popping?

View results

What are the restrictions on being reelected into the US House of Representatives?

View results