0
The starter is attached by 2 bolts.
First, unhook the battery.
Next, the thing to the left of the battery holder is the cruise control. You need to move that out of the way to give you room to work.
There are 2 bolts on the starter. Try to soak with WD-40 to loosen them up. If you can loosen both bolts with a wrench or rachet set, unhook all the wires attached to the starter and remember where they came from.
The new starter will bolt on the exact same way.
Reattach the wires and put back the cruise control and battery holder, as well as the battery.
These bolts could be stipped if you dont use high quality six sided cup. If they in the process they are stipped get Craftman extractor cups which work flawlessly and install new high grade bolts with washers. These extractor extract the bolt instantly and extremely easy.
Wiki User
∙ 14y ago
Wiki User
∙ 18y ago1. Disconnect negative battery cable. Disconnect positive battery cable at the starter. 2. Disconnect remaining electrical connections at the starter soleniod. 3. Remove the nuts and or bolts holding the starterr to the bell housing and pull the starter towards the front of the vehicle. Intallation in reverse, but make sure that the starter drive teeth are engaged with the flywheel teeth... You will have a very tight space in this job and you might need to modify some wrenches to do the job easier...
Wiki User
∙ 12y ago1. Disconnect battery connectors, or at least the positive side.2. Disconnect the connections on the starter, should be 2. 1 is a locking push on connector the other has a nut. 3. Remove the bolts that hold the starter to the engine. On the V6 there are 2 bolts, top and bottom. On the 4 cly there can be 3 of them, top bottom and out to the side.4. Here you have to make a judgment call depending on the type of vehicle. Some, like the 4 cyl 4 wheel drive model, will allow you to easily remove out the bottom. The V6 4 wheel drive model allows you to remove out the wheel well above the suspension arm. This is a tight fit and you need to turn it just so to get it to fit.5 reinstall the same way you removed.
Wiki User
∙ 17y agoIf it is like my 98 Camry, the starter is sitting right on top of the transmission. Should be 2 bolts and 1 wire to unhook. It is not very big so you have to really look for it.
Wiki User
∙ 16y agothats a good question there is not much room there
Add your answer:
Earn +20 pts
How do you remove a broken starter bolt on a 1996 Toyota Camry 4-cylinder?
get a tap and die set and follow the instructions.
Can the starter solenoid be repaired on a 1996 3.0 liter Dodge Caravan starter?
Depends on the type of starter, or I should say manufactuer.
Where is the starter on a 1996 gmc jimmy?
Look at the lower rear end of engine
Where is the 1996 Toyota rav4 exhaust system?
The exhaust system on a 1996 Toyota is located underneath the vehicle. This system runs all the way from under the motor to the very back of the vehicle to the muffler.
Where is starter relay switch for 1996 Toyota corolla?
the starter relay is located in a black plastic box on the driver side of the engine compartment
How do you replace the starter on a 1996 Toyota Tacoma Xtra cab 4wd V6?
You should remove the positive cable from your 1996 Toyota battery. Remove the cables from the front of the starter. Remove the starter retaining bolts. Reverse the process to install the new starter.
Where is the ecu located on a 1996 Toyota 4 runner?
where is the ecu located on 1996 Toyota 4 runner
How do you tell if the starter from a 1996 Toyota Tercel is bad?
Remove it and have it tested at an auto parts store
Where is the starter relay switch on a 1996 Toyota Corolla?
where is the starter relay switch on a 1996 Toyota corolla
How do you replace the alternator on a 1996 Toyota 4Runner?
how to replace alternator on Toyota 4 runner 1996
How do you replace starter on 1996 Toyota Camry?
Remove the battery and the cruise control actuator. The starter has two bolts holding it in. Remove the bolts and wiring, then install the new starter. Re-install the cruise control and battery.
Where is the starter on a 1996 Toyota Camry?
The 1996 Toyota Camry starter is located near the front of the engine, at the bottom. You can follow the positive battery cable from the battery to the starter.
How do you remove a broken starter bolt on a 1996 Toyota Camry 4-cylinder?
get a tap and die set and follow the instructions.
Where is starter solenoid located on 1996 Toyota tacoma?
A starter solenoid will be located on top of the starter assembly. A 1996 Toyota Tacoma starter assembly is located under the vehicle next to the passenger wheel.
What is the oil capacity of a 1996 Toyota Runner?
4.75 quarts
How do you remove the starter in a 1996 Chevy 2500 diesel?
how to remove starter on 1996 chevrolet 2500 with 6.5 diesel engine
How many filters does a 1996 Toyota 4 runner have?
at least 3
