0
press and hold the clock button then push the seek/scan to change
Wiki User
∙ 16y ago
Wiki User
∙ 17y agoThe clock may be synchronized with the clock of the radio (factory). Adjust the radio clock using a pointed object (toothpick, ink pen) in the hour and minute buttons.
Wiki User
∙ 17y agoOn my 1999 F150, you press the clock button then use the left and right scan buttons to set it. Don't know if this will work for a '94 or not.
Wiki User
∙ 15y agoWhile holding the clock button use the seek buttons to adjust the hour and the tune buttons to adjust the minutes
Wiki User
∙ 15y agoWith the radio off,press the set button and then press the volumn to go up or down.
Add your answer:
Earn +20 pts
What does LE or LS or LXT mean on a car?
"Limited Edition", "Luxury Sport", and "Luxury Extreme Technology" are among the meanings of a car's markings "LE", "LS" or "LXT".Specifically, the "LE" marking identifies the small number of such vehicles produced. The "LS" marking indicates an edition with more desirable accessories and options. The "LXT" marking points to the cutting-edge, state-of-the-art technology of the vehicle and its component parts.
Is Makita LXT tools more powerful then Dewalt XRP tools?
DeWalt XRP is just a battery. It stands for "Extended Run-Time Performance" It just means it has a longer lasting battery, not that it's really more powerful, but the good batteries are generally put on the better DeWalt tools. The voltage of the battery is going to be the major limit to how much power it has. The advantage of the LXT tools is the power to weight ratio the LXT is 18 volt with the weight of 12 volt tools. Its not more powerful in over all power but it is more powerful for its weight class.
What is the top speed of the Makita 18V LXT?
There are different models of the Makita 18V LXT. For the LXT211, the speed varies between 0 and 2,300 RPM. The LXT218 18V has a 2-speed all-metal transmission. These range from speeds of 0-400 RPM and 0-1,700 RPM. The top speed for this particular drill will vary with the model type selected.
How do I pick up the police on my midland lxt 480 two-way radio it has 36 channels?
The Midland LXT 480 radio operates in the 462-465 MHz GMRS/FRS band. The channels marked #8 to #14 operate on license-free frequencies with low power. All of the other channels require an FCC license, and there are severe penalties for using them to transmit without the proper license. Fire, police, ambulance, etc. don't operate in the GMRS/FRS frequency band. So you can't hear them with the LXT 480 unless you get into the guts of the radio and modify (rebuild) it.
How to make a 3D pentagonal prism?
To make a right pentagonal prism, start with two congruent pentagons, with sides of length P, Q, R, S and T units - these can all be equal, if you like. If the prism is to be L units long, then you will need one rectangle of each of the following dimensions: LxP, LxQ, LxR, LxS and LxT. The pentagons need to be parallel and facing each other at a distance of L units and then the rectanles will join the corresonding edges of the pentagons.
How do you replace the front brake pads on a 2002 Ford Escape?
If your not used to working with antilock/traction control vehicles, you may want to leave this job to a professional. There are some things that you need to be aware of before proceeding with the job. But, if you decide to go on with this, You may want to go to a car parts store, or book store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library. on front of a 2k1 v6 4x4 LXT Escape, loosen all 5 lugnuts, jack up vehicle, and place on a jack stand, remove wheel, using a T47 star tool unbolt caliperfrom it's mounting point ater removing the 2 plastic caps, caliper would move out of the way, the front side pad would come out easily, the inside pad is held on by 3 thin metal taps inside the caliper wich that pad is also easly removed. all is reverse as removal.
How do you remove a door panel on a 2002 Chevy Tracker?
If its the same as a 2003 lxt sport tracker, should be a screw in the little pocket thing and a screw behind the handle. the handle is snapped in by plastic and has a string to hold it to the opening mechanism that needs to be taken off. then just use a screwdriver to pry the bottom clips off. the panels are all held on by plastic snaps that break easily, get ready to solder them back on or go to Canadian tire for some little plastic bits. when u pry a couple clips off just pull the panel up and over the lock button.
What brands of bits are compatible with a makita bdf452 18v lxt lithium drill and what are the essential bits?
First off, Makita tools are very good. A few bits should come with the drill. It sounds like any standard cordless drill bits would work. You want a main bit that you use primarily. That is about 2 inches long and is a #2 phillips head. Sometimes it has a flat head on the other end which is handy. You may want another two inch bit with a flat head. Buy a good one for a buck extra (Vermont American bit, etc...)so it won't get stripped quickly. You can buy lots of bits that are two inches long, but you want a bit set. It has a bunch of different smaller bits that fit into a 2 inch chank with a socket-type end. There is just a ton of different stuff that you can buy, and you can probably find lots of different kits that contain all of this. You can use drill bits that are made for cordless drills. A normal drill bit won't work. The base end of the bit is made to slide down/ fit into the drill. I have some of those drill bits, and I also have some that make a little divit into the wood so the screw-head fits in nice and snug. Mine are made at Ryobi, and I bought them at the Home Depot. You can buy replacement drill bits to fit into the base. That's pretty handy because you can break a lot of bits without replacing the whole thing.
