0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Remove upper mounting bolt from starter on a 2002 Honda CRV?
(1) You must first remove the bracket clamp that retains the wiring harness to the trnsmission. (2) Disconnect the starter wires from the starter and that should give you the clearance you need to get a wrench on the upper starter bolt. (3) then remove the lower bolt.
Where is the starter located on a 1991 Plymouth laser?
remove you battery box and right below ur intake u will see a wire running to a bolt remove that bolt and the bolt below that and you will have to go underneath the car to get the starter out
How do you replace a starter in a 1999 Dodge Durango?
disconnected neg battery cable remove bolt and nut attaching starter to bell housing. turn starter slightly and disconnect wires from starter. remove bolt from intermediate shaft at steering box and position out of the way. then remove starter though fender well. reverse procedure
How do you remove and install a starter on a 2000 Plymouth Voyager?
For the 3.0 liter engine. Disconnect negative battery terminal. Locate starter at lower front of engine by engine fans. 2 bolts holding starter in, upper and lower. Remove lower bolt 3/4 way- easy to see, upper bolt go from top of engine to remove (need extensions). Completely remove lower bolt and remove positive battery connector and signal wire on top of starter. Install reverse of removal.
How do you change a starter on a Saturn vue?
1. Remove the negative battery cable. 2. Remove wires on the starter. 3. Remove the two mounting bolts. They have 15mm heads. (The top bolt is hidden and hard to get to.) You may have to remove the solenoid (on top of the starter) to get to it. 4. Remove starter Replacement is the opposite of the removal.
How do you replace the starter on a 91 mx6?
3 bolts on starter, pull ,remove wires from start insert new starter and reattach wires and bolt into transmission
How do you fit vauxhall combo starter motor?
This is how to remove it..... fitting is same but in reverse. First, remove the battery, taking off the negative connection first. Remove the 4 bolts holding the battery tray in place (13mm socket) Underneath the car, at the back of the engine, remove the pozi drive screw holding the LT lead to the back of the solenoid, remove the top nut connecting the thick cable to the back of solenoid (I found this easier to do once the starter was hanging loose) Back above the engine, loosen the 19mm bolt that holds the starter motor to the gearbox (it's a tight squeeze to get access to it) Then back underneath, loosen the bottom starter motor bolt (14mm) Back above, remove the 19mm bolt, underneath again and while supporting the starter, remove the 14mm bolt. The starter can then be jiggled about to remove it completely.
How do I remove a starter on a 2003 Ford Expedition?
First remove the battery cables from the battery. Remove the electrical connections to the starter and label for replacement. There are 3 bolts - 13mm. The bottom bolt is also the ground terminal, therefore you will need a deep socket for that bolt. The other two are accessable ideally with about a 7" extension to your socket wrench. The top bolt is on the top of the starter and I could fit my hand up there to feel it and place the socket. The 3rd bolt is between the bottom and top bolts. Remove the 3 bolts and the starter falls right out. I replaced with a remanufactured, lifetime warranty starter from Pep Boys for about $120.
How do you remove and replace 2000 intrigue crankshaft sensor?
This is a quick answer. Its above the starter going into the side of the block. (front side of the engine) Disconnect the battery. Remove the starter. Remove the wore plug into the sensor. The sensor has 1 bolt holding it in. Remove the bolt, you may have to wiggle the sensor at the base a bit as you pull it out. Replace, and make sure it is pushed in all of the way. Replace the bolt, wire plug, starter, reconnect the battery. If you have ever removed or replaced a starter this is cake, that is the hardest part of the job. Rich
Where is the crankshaft sensor on a Dodge SRT 4?
its just below the starter. it might be a bit difficult to remove since you're going to have to remove the starter itself to get to the bolt. good luck.
Where can you find instructions for the installation of the starter and solenoid on a Cavalier?
Somewhat easy to do. You can see it from the top of the engine. You'll have to get at it from underneath. A few bolts, a few elect. connections. Make sure you disconnect the batt first! To remove starter on a 96 Cavalier with a 2.4L engine 1.Disconnect battery 2.Disconnect air inlet duct from throttle body. 3.Remove top starter bolt. 4.Raise and safely support car. 5.From under the car remove second starter bolt. 6.Remove the wiring from the solenoid. To install starter 1. Connect wiring to solenoid 2. Put starter in position and put the 1st bolt in from top of engine and tighten 3. Put starter bolt in the 2nd bolt and tighten. 4.Connect air inlet duct. Connect battery
How do you fix a starter on a standard 1993 Saturn coupe?
Depends what's wrong with it but most likely needs rebuilding. Difficult to remove in driveway but can be done...Disconnect battery. Starter is located on the back of the engine. Remove the 10 & 13 mm nuts on the solenoid, then remove the 2 13mm bolts that hold the starter to the block. For the upper bolt you need an extension (6inch) to reach the bolt head. Remove the starter and either have rebuilt or install new.
