0
How do you install generalaire humidifier 1042 damper assembly?
Wiki User
∙ 12y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Does the 1995 s10 blazer have a steering damper?
The 1995 s10 blazer may have a damper. The damper will look like a shock connected to the steering assembly. You can look under the front end to see for sure.
How do you replace the front shocks on a 1999 Saab 9.3 convertible?
Put front of car on stands or on lift. Remove wheels. Remove three or four (depending on model) strut/damper mount tower nuts (under hood). Remove strut/damper to spindle bolts. Remove damper/spring assembly and replace with new. You may replace it as a complete assembly or damper only. If you plan on replacing the damper only, you'll be required to remove spring from old damper and transplant it on to the new Cheers
Location of fuel pressure damper 97 Chevy Tahoe 5.7L engine?
Damper? I assuming you are talking about the regulator it is usually on the upper intake connected to the fuel injector assembly.
How do you install a steering stabilizer own your Chevy truck?
1952 chevy truck does not have a steering damper, where and how to mount steering damper on my 1952 chevy truck .thanks jim
How do you replace front and rear struts on a 95 Honda civic coupe?
-Front-1. Raise and safely support the vehicle.2. Remove the front tire and wheel assembly.3. Remove the brake hose clamps from the damper and the damper pinch bolt.4. Remove the damper fork bolts and remove the damper fork.5. Remove the two upper flange nuts and remove the strut assembly.To install:6. Loosely install the damper assembly into the damper fork with the aligning tab facing inside.7. Install the damper fork on the halfshaft and lower arm. Install the damper in its fork and align the tab with the damper fork slot. Hand-tighten the nuts and bolts.The mount base nuts should be tightened once the damper is under vehicle load.8. Tighten the self-locking damper pinch bolt to 32 ft. lbs. (44 Nm).9. Tighten a new self-locking damper fork nut to 47 ft. lbs. (65 Nm) while holding the damper fork bolt.10. Install the brake hose clamps with the two bolts.11. Install the two upper flange nuts for the damper assembly to secure it to the frame but do not fully tighten them.12. Lower the vehicle and tighten the flange nuts to the strut under vehicle load. Tighten to 36 ft. lbs. (50 Nm).-Rear-1. Support the rear of the vehicle securely and remove the rear wheels. Support the rear axle housing securely with a floor jack.2. Remove the damper access covers from inside. Remove the cap and unscrew the two nuts on each side.3. If you are removing the shock absorbers only, lower the axle just enough for the rod to clear the body. Otherwise, lower the axle until the shock absorbers and spring parts are all free. Remove the springs, upper and lower seats (if necessary), then unbolt the shock absorbers at the axle and remove them.4. If springs have been removed, install the upper spring seats into the body. Place the lower spring seats on the axle and position the springs on the seats.To install:5. Install the shock absorbers upright in the axle housing and bolt them loosely at the bottom. Then, gradually raise the axle with a floor jack until the piston rods of the shock absorbers can be guided through the holes in the vehicle body. As you do this, also check that the springs are in the proper positions.6. When the piston rods are well through the body holes, install the two locknuts on either side. Using an Allen® wrench to hold the nuts, and tighten the lower nuts to 14 ft. lbs. (19 Nm) and the upper to 16 ft. lbs. (22 Nm). Install the cap and access cover. Install the wheels and lower the vehicle to the floor. Tighten the lower shock absorber mounting bolts to 60 ft. lbs. (83 Nm).
What is an axle damper on a Ford Mustang?
The axle damper is a horizontal shock absorber that connects from the rear axle to the frame of the mustang. When you pull the rear tires off, you will see the damper behind the brake assembly . It is standard equipment if the mustang came with the factory handling package.
What is the layer of rubber between the two pieces of metal that are mounted to the stub on the end of the crankshaft called?
The assembly is called a "Harmonic Balancer" or "Harmonic Damper" in Europe. The Rubber acts as a damper to smoth the engine vibrations at certain speeds. The Rubber is not available seperately so most people won't know its called a "Damper"
How do you change a crankshaft sensor on a 1987 olds delta 88?
You have to remove the Vibration Damper first, then you will have clear access to the Crank sensor. Make sure when you reinstall it, the wires don't get caught in the Damper assembly and you have clearance where the sensor mounts. Easy fix.
What is another name for harmonic balancer?
AKA, crank pulley damper, crankshaft damper, torsional damper, or vibration damper.
Where is the damper on a furance?
were is the damper on a furance
How is damper made from grass seeds?
well they pick grass and put it in the damper and mix it and it becomes damper
How do remove and replace a strut on a 97 Nissan Sentra GXE?
Honda calls it a damper. If you want the front damper. Remove the brake hose clamps from the damper remove the damper pinch bolt (on the bottom). Remove the damper fork bolt. then remove the damper by removing the two 10 mm nuts on top. Do not try to Disassemble the Damper without a spring compressor.
