answersLogoWhite

0

How do you drill a stud from a car wheel?

Updated: 4/28/2022
User Avatar

Wiki User

13y ago

Best Answer

to replace a wheel stud, depend on the type of car or truck, jack it up and block it. remove the affected wheel and use a hammer and a punch to drive out the broken stud. most automobiles have an access hole to replace studs with out removing any more components. however some do not. to install place stud in hole and use some washers and a lugnut to mount in place.

User Avatar

Wiki User

13y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you drill a stud from a car wheel?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you remove a lug nut when the wheel stud is also turning on aluminum wheels?

You will have to drill or cut the stud off.


What car is this of 4 stud 3inch stud pattern 74mm centre bore 4 j wheel?

check lugnutpatterns.com


How do you fix a pressed in rocker arm stud that won't stay in?

drill a small hole through the stud boss,stud and tap a pin through both boss,stud. This is called stud pinning, you can get a kit from napa for about 20.00 bucks comes with studs,drill bit.


How do you replace a broken wheel stud in front wheel?

Jack the car up and remove the front wheel. Use a jack stand for safety. Rotate the axle until the stud is over the hole in the backer plate. Hit the stud with a hammer, this will take many blows. The stud will pop out. Slide the new stud in, then stack several washers on the shaft and put a lug nut on. Tighten the nut to pull the stud up tight into place. Reinstall the wheel, and over the next few days, keep checking the tightness of the stud to keep it snugged up.


What type of drillbit used to drill broken manifold stud?

The type of drill bit used to remove a broken manifold stud is an extractor or easy out. A hole is drilled into the stud and then the extractor is used to dig in and unscrew the bolt.


How do you fix a press stud?

You could press in a new, oversize stud, cross drill and pin the stud, or have the head machined for screw-in studs.


Can you put front wheel drive wheels on a rear wheel drive car?

if it has the same stud pattern yes. hope this helpsYes, as long as they fit.


How do you replace wheel nut studs?

See the attached links for some good instructions on how to replace the wheel studs. It generally breaks down into a few steps: 1) get the right tools together (and the replacement stud if you know the size) 2) jack up the car and remove the wheel 3) remove the brakes 4) knock out the stud to be replaced. (if you didn't get a replacement stud before you started, take the stud you removed with you to the auto-parts store to get it matched up to what you need) 5) Insert the new stud 6) screw a nut onto the stud and tighten it until the new stud is seated 7) reinstall your brakes and put your wheel back on


What tools do I need to use this Is this something I can do myself?

You can do this yourself. you will need a drill with drill and driver bits, a stud finder and a level.


How do you remove a broken stud from the water outlet neck on an aluminum intake manifold?

Are you handy with a center punch, and a drill? If so, the best way to do this is to drill a hole in the center of the stud, and along with penetrating oil, an/or heat from a torch, use an easyout to extract the broken stud from the intake.


How do you change front wheel stud on Chevy 1992 s10 blazer?

The front wheel stud on a 1992 Chevy Blazer S10 can be changed by jacking the vehicle up, removing the wheel, and unbolting the caliper. The rotor assembly can then be removed, and the wheel stud pressed or hammered out of its seat.


How do you replace broken stud on 95 f 150 4x4?

Are you asking about a wheel stud or exhaust stud, please clarify