0
Why does a 100 amp circuit breaker panel have 30 breakers that are 20 amps?
Wiki User
∙ 11y ago
There is no reason, it is most likely what the the installer did.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Is it safe to have 200 plus amps in breakers inside than 90 amps on the main service breaker outside?
I am assuming by your description that the panel is protected by a 90 amp breaker and the breakers in the panel when added up is 200. This is okay as long as your 90 amp breaker trips on a regular basis. It is typical for the breakers to add up to more than the main breaker under the assumption that you would rarely be running each circuit at its maximum capacity.
If an electrician have a circuit that pulls a load of 10 amps what size breaker must that circuit be protected by?
If you are talking about a breaker in a house panel then a 15 amp breaker would be used. It is the smallest amperage breaker that you will find in a house panel.
What circuit breaker to install for 10 amp 250 volt circuit?
You need a breaker rated for 10 amps and 250 volts. The breaker must also fit properly in your panel.
Is a circuit breaker better than a glass fuse?
Each device has its own special use. Glass fuses can protect circuit at very low amperages. They are usually used to protect printed circuit boards and control panel circuits. Breakers protect circuits from short circuits and overloads. These devices are used in service distribution panels to protect the wires that feed the loads. Circuit breakers can be from 15 amps up into the thousands of amps.
How does you caluclate the Horse power in 250 amp circuit breaker?
First of all, circuit breakers are rated in amps, not horsepower. Theequivalent between HP and electricity is 1 HP = 746 watts. That is a 1 HP motor requires 746 watts of power to operate it , regardless of the voltage. If you have a 250 amp circuit breaker, it is likely the main breaker to your residential panel. (?) The potential HP the panel could provide could be determined by multiplying the 250 amps times the panels voltage (208,220, 240) and divide the sum by 746.
Is it safe to have 200 plus amps in breakers inside than 90 amps on the main service breaker outside?
I am assuming by your description that the panel is protected by a 90 amp breaker and the breakers in the panel when added up is 200. This is okay as long as your 90 amp breaker trips on a regular basis. It is typical for the breakers to add up to more than the main breaker under the assumption that you would rarely be running each circuit at its maximum capacity.
What is the rating of the main circuit breaker of the 105kw power distribution panel?
To answer this question a voltage must be stated. Main breakers are rated in amps. This is the formula for amperage. I = W/E. Amps = Watts/Volts. As you can see a
Why does the main circuit breaker trip but not the smaller branch circuit breakers?
If the main breaker has ground fault detection, and the fault is a ground fault, then only the main may trip. Also if the fault is a direct short, the fault current may be several thousand amps, much greater than the trip point of both breakers. Breakers have an I^2T curve (current squared-time), which is an indication of how fast the breaker will trip at a given overload. When both breakers are overloaded, the breaker with the faster I^2T rating at that current level will trip first. This would be an indication that the breakers are improperly specified or adjusted.
If an electrician have a circuit that pulls a load of 10 amps what size breaker must that circuit be protected by?
If you are talking about a breaker in a house panel then a 15 amp breaker would be used. It is the smallest amperage breaker that you will find in a house panel.
What is the rating of the main circuit breaker of the 60kw power distribution panel?
200 amps
What circuit breaker to install for 10 amp 250 volt circuit?
You need a breaker rated for 10 amps and 250 volts. The breaker must also fit properly in your panel.
What is making capacity of a circuit breaker?
Hard to define... A four year old child has the strength to physically "make" a typical household circuit breaker, while a teen would be able to "make" a typical industrial circuit breaker. (The latter breaker being physically much larger than the former.) Circuit breakers have their "breaking capacity" rated in AMPS. A typical household breaker is rated at 20, 30 or 50 Amps. Industrial breakers might be rated at 500 amps or a thousand or even more. Hope this helps but if it didn't answer your question, please rephrase it and ask again.
Is a circuit breaker better than a glass fuse?
Each device has its own special use. Glass fuses can protect circuit at very low amperages. They are usually used to protect printed circuit boards and control panel circuits. Breakers protect circuits from short circuits and overloads. These devices are used in service distribution panels to protect the wires that feed the loads. Circuit breakers can be from 15 amps up into the thousands of amps.
How does you caluclate the Horse power in 250 amp circuit breaker?
First of all, circuit breakers are rated in amps, not horsepower. Theequivalent between HP and electricity is 1 HP = 746 watts. That is a 1 HP motor requires 746 watts of power to operate it , regardless of the voltage. If you have a 250 amp circuit breaker, it is likely the main breaker to your residential panel. (?) The potential HP the panel could provide could be determined by multiplying the 250 amps times the panels voltage (208,220, 240) and divide the sum by 746.
Can a sub panel from a 15 amp breaker be used with a branch circuit with 20 amp breaker?
Answer for USA, Canada and countries running a 60 Hz power supply service. Yes you can add these two breakers to the sub panel. You will have to keep in mind the fact that if the total loading of the two breakers exceeds 30 amps the 30 amp sub panel breaker will trip. If you use the 20 amp and the 15 amp loads individually then you will be under the 30 amp feeder sub panel breaker and good to go. With feeders of 3 conductor #8 the 30 amp breaker can be increased to 40 amp. If there are large motor loads involved this answer will change as starting current has to be calculated into the equation. View discussion page for additional information.SAFETY ADVICE Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energizedIF YOU ARE NOT REALLY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
Is it OK to have 250 A of breakers in a 100 A panel?
Yes. Many installations have breaker totals higher that the main breaker of the panel. It is worked on a percentage basis. Not all of the breakers will be on at the same time. In a home, on a 100 amp panel the average load is 50 - 60 amps. The 100 amp main breaker is protecting the 100 amp rated panel board. If the load current goes higher that the panel board is rated at, the main breaker will trip to protect the board.
What size fuse for a 20 HP DC motor?
20hp = 14.92kW 14.92kW / X Voltage= X Amps Rule of thumb for fuses: X Amps x 1.5 = Y Amps Fuse Rule of thumb circuit breakers: X Amps x 1.2 = Y Amps Circuit Breaker
