0
your beam selector lever is prob. busted and needs 2 be replaced. or its a wiring prob. check some fuses and the wires to the selector if everything is ok there, then you prob need a new selector
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
If your Jeeps air bag light is on can the air bag go off any time?
Generally, when the light is on the airbag is disabled.
Why are there no tail lights on 1999 jeep grand Cherokee bulbs are new?
If dash and parking lights do not work - check the fusesMay also be a bad headlight switchThe tail lights and brake lights on my 2002 would not work at the same time. Had to replace whole tail light assembly. Was told problems with jeeps-the circuit boards in older jeeps overheat and short out.
Does justin bieber stay in atlanta most of the time when not recording?
Justin Bieber does stay in Atlanta for a period of time each year. However, he seems to stay in California more.
Who sang Come back and stay for good this time?
Paul Young. ca. 1983
What transfer case is needed to swap a full time 4x4 for a part time 4x4 2004 Jeep Grand Cherokee?
The part time transfer case in a 2004 Grand Cherokee was a NP242. To swap from a NP247 to a NP242 you may also need to change drive shafts and axle yokes.
Taurus high beams stay on all the time they will not shut off even when the key is off also dome light stays on ocassionally when it should not?
If you have a Ford Taurus and the high beams stay on all the time, chances are that you have a defective control switch. The dome light uses a separate switch but is likely to have the same problem. To correct the problem, both switches should be replaced.
Do Jeeps have fog lights and high beams only?
on all Chrysler vehicles that i have seen you can only have either the fog lights on or the high beams. the reason is if you run both it puts a strain on the electrical system and could actually cause a fire in the steering column there is a way to get them to both come on at the same time tho i don't recommend it. if you want its your vehicle you'll have to do some research on how tho. -mechanic for 7+ years
You must dim your high beams for oncoming vehicles by the time they are within feet of your vehicle and dim your high beams when the vehicle you are following is within feet?
150 meters
Why would the high beams on a 1994 Thunderbird work when the low beams do not?
Headlights have two filaments; one for low beams and one for high beams. There is a good chance that the low beams are burnt out. This doesn't necessarily mean that the high beams won't work. However, it's not too common for both low beams to burn out at the same time. Of course, it could be a fluke. I would replace the headlights with new ones and then go from there.
Why high beams are on all the time 98 5.9 limited?
Dimmer switch broke??
Why dont high beam and low beam headlights stay on together. Lights work but low beams turn off when high beams are on.?
In most cases the high and low are separate elements in the same bulb and cannot work at the same time. Headlights pull a lot of power and to have them run together would be too much for your charging system to handle at once, not to mention the heat they would produce. Fog Lamps and Low beams and Fog Lamps and HI beams. Fog Lamps and HI beams, in many states, you are not permitted to run HI Beams and Fog / Driving lamps simultaneously. There is an SAE directive on this. There is either a relay or DRL module that prevents the Fog/Driving lamps to be energized when the HI beams are activated.
Why would both low beams go out at the same time but the high beams still work on a 1996 miata?
check the wiring at the hi-low switch.
Why do Low beams work high beams don't indicator light on all the time in 1996 Pontiac sunfire?
Normally caused by faulty dimmer switch.
Where can you buy 20000 Jeeps?
Your local Jeep dealer may be able to help you with that. 20,000 Jeeps is a lot of Jeeps so they may not all be delivered at the same time.
You may use your high beams only if there is no oncoming traffic for?
The traffic laws vary as to distance in almost ALL states. The reasonable answer is this - - If you can see the lights of the oncoming car, then he can see you and is probably being blinded by your high beams. Dim them whenever you can see oncomiong traffic.
How do you turn on the high beams in your Subaru Forester?
The high beam switch is activated by the turn signal lever on the left side of the steering wheel column. There are basically three settings - On, Off, and Flash. On is when the lever is pushed away from you, Off is with the lever in its normal position, and Flash is with the lever pulled towards you. To "flash" the high beams, pull the turn signal lever towards you. The high beams will come on for as long as you pull the lever towards you. Releasing the lever will return it to its normal position and the high beams will go off. This will work regardless of whether you have the headlights turned on or off. Among other things, flashing is good for giving someone right of way, for letting someone enter a highway, or to let another driver know that they are blinding you with their high beams! Pushing the turn signal lever away from you will cause the high beams to come on (only if the headlights are turned on at the time) and stay on until you pull the lever towards you again. When you push the lever away from you it will stay in that position until you pull it back to the middle position again. This setting is good for driving on unlit streets. When the high beam switch is activated (On or Flash) you should see a blue light on the dashboard that looks like a little headlamp.
Fog light switch on the 2002 Ford Explorer XLT?
It's the same switch as is used to turn the headlights on, just pull it out. The driving lights will not work at the same time as the high beams so make sure the high beams are turned off.
