0
The part the enables the blower to have multiple speeds in the blower resistor.
When one of those goes bad, you'll have only the high speed setting that works.
Luckily it's an easy and not expensive fix.
See "Related Questions" below for more
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Why do speed 1 and2 fan speeds do not work and 3 and 4 do on my 95 ford windstar?
Blower Motor Resistor Pack is defective.
What could be wrong if the AC blower on a 1995 Ford Windstar will not blow air?
fuse, wiring, blower motor, blower motor switch, blower motor resistor
Where is the speed control device located on a 1995 ford windstar?
The speed control device or speed sensor on a 1995 Ford Windstar is located on the transmission. It is a plug in just behind the bell housing.
Why might the fan heat and AC not be working on a 1998 Ford Windstar?
it could be the blower switch
Which fuse controls the drive and passenger windows on a 95 ford windstar?
what the number of the fuse on window 95 windstar diver side
2000 Ford Windstar Why does my back heater not blow at all?
The blower on the back heater may need to be replaced on the 2000 Ford Winstar.
Where is speed sensor located in a 98 ford windstar?
on top of the transmission
Where is the blowerheater switch located in the 2003 ford windstar?
it is the switch you use to turn blower up and down.if you mean resistor it is in the heater box next to blower motor
Ford Windstar 1999 tail lights stay on all the time?
It sounds as if there is a problem with the rear electronics module in the Ford Windstar. This controls the front and rear lights and it is located in the back in the cubby with the jack.
Where is the blower motor resistor on a Ford Windstar?
What the blower resistor doesThe resistor provide the blower fan with multiple speeds.A blown / failed resistor will result in the heater fan blowing on HIGH speed only.The Ford Windstar blower has a resistor block that controls the various speeds of the blower motor. It is located on the passenger compartment side of the blower housing and can be replaced in five minutes.AnswerIf it is in the same spot as the 98 windstar, then it is located under the dash of the passenger side. It is actually really easy to change. Two screws and the plug and it is removed. AnswerThe blower motor resistor pack has failed. Replace it. On my 2000 windstar rear fan although it has a multi speed selector is only wired up in the harness for single speed, the front fan does have multi speed.AnswerOn the evaporator case. AnswerOn a 98 Windstar it is underneath the front blower motor and has 4 wires on a plug. The glove box doesn't need to be removed or opened. It's held in by 2 8mm screws. You may very well have a blown fuse, check all the fuses for the air conditioning system, there is a box located on the driver side of the vehicle in the drivers foot well, a diagram with all the fuses and their amperage will be on the cover, remove the cover and locate the blower fuses for the A/c. If the fuses are not blown, then it may very well be that the blower motor is damaged or the control is not working properly. It is recommended that you take it to professional service shop if this is the case due to the many probabilities of a vaccum leak or a electrical problem that is best solved by the professionals.Its on the passengers side under the dash and its held in place by two screws which will located on the a/c evaporator housing...................
Why don't my heater blower work in my 1998 ford Windstar 3.0L?
Maybe it's bad. Have you tried changing it? Sound logical to me.
How do you turn on highbeams for a 1998 Ford Windstar?
To turn on the highbeams of a 1998 Ford Windstar, bring your lever that controls the wipers toward you and release that turns the highbeams on. To turn off highbeams just push the lever towards the dash.
