answersLogoWhite

0


Best Answer

Check at sears.com under partsdirect to see if parts are still available for your machine. if not, see if there is a vacuum repair shop in your area and check with them.

User Avatar

Wiki User

12y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Where do I find a Brush roller for a Kenmore Upright Vacuum Model 116.39139990?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

When was Roller Coaster - Red Bacteria Vacuum album - created?

Roller Coaster - Red Bacteria Vacuum album - was created on 2006-01-01.


Why has your Dyson vacuum started screaming at you?

The drivebelt may be slipping, or a roller bearing dried out.


How do you replace the belt after taking the cover off of a fantom fury vacuum cleaner?

You slide out the roller brush and put belt around it and slide it back in. Then you put belt onto the motor. The roller brush is a little hard to slide out.


Is the phrase Atlantic Ocean a common noun?

The proper noun Atlantic is a short name for the Atlantic Ocean.The common noun is an ocean.The word 'Atlantic' is also a proper adjective, a word to describe a noun as of or from the Atlantic Ocean.


When I put a large new comp cam and roller lifters in a small block 350 at idle it has low vacuum from carburetor which effects the brake booster and doesn't stop like it should what can I do?

You will have to install an aftermarket Vacuum canaster. You can by them at a high performance shop.


What is the best vacuum for both carpet and hardwood floors?

What is probably the best vacuum for this dual application isn't one made by a particular manufacturer, but one t hat has a special feature. That feature is a roller (brush roll, beater bar, or other name) that can be turned on or off either mechanically or electrically. A roller is arguably the best way to clean carpet as the bristles on that part loosen debris for efficient pick up. But the roller creates a lot of air turbulence, and this can actually be seen to push debris away from the nozzle when the machine is used on bare floors. Debris on a bare floor doesn't need the loosening effect of the roller. It just needs to get under the roller housing to get caught up in the air stream that carries it to the bag/filter.


How soon can you use automatic pool vacuum after Hydrazzo re-plaster?

30 days of no auto cleaners and no roller type vacuums has been the standard in the industry for many years


How do you install a hoover u5077-930 vacuum belt?

Release the 2 tabs and remove the trim and roller brush. Take a Dremel motor tool with a cutting blade and cut a access


Does the Rainbow vacuum ever break down?

A Rainbow vacuum is subject to motor failure like any other vacuum. It is also possible to see a problem with the power cord. The machine is plugged in and unplugged and the cord wrapped up during use. This wears on the cord. If the machine has a powered brush nozzle, the belt and motor there are subject to failure, and the brush roller can wear out or experience bearing failure.


How do you replace dc17 belt for Dyson vacuum?

Before you do anything make sure that the machine is unplugged.1. Loosen 3 screws from bottom plate using flat-head screwdriver and remove it.2. Wiggle roller until it pulls straight out.3. Squeeze new belt and loop it over metal drive gear (you'll easily see the gear).4. Keeping belt on gear, insert edge of roller through belt and rotate the roller while pushing it through belt until it is inside the belt, then continue rotating roller and sliding it over until belt is in position over gears on roller.5. Insert roller into slots on that it came out of, reattach bottom cover and its done.


How do you Replace belt on Dyson dc 17 vacuum?

It is very simple to do:1. Loosen 3 screws from bottom plate using flathead screwdriver or coin edge and remove it.2. Wiggle roller until it pulls straight out.3. Squeeze new belt and loop it over metal drive gear (you'll easily see the gear).4. Keeping belt on gear, insert edge of roller through belt and rotate the roller while pushing it through belt until it is inside the belt, then continue rotating roller and sliding it over until belt is in position over gears on roller.5. Insert roller into slots on that it came out of, reattach bottom cover and its done.


What has the author Donald Roller Wilson written?

Donald Roller Wilson has written: 'Donald Roller Wilson' 'Roller' -- subject(s): Catalogs