answersLogoWhite

0


Best Answer

Mr.Stoeber made the twine ball in 1953.

User Avatar

Wiki User

14y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: What year did MrStoeber start making the twine ball?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

In what year did Mr. Stoeber start making the twine ball?

In 1953 mr. stoeber started making the twine ball.


What year did Mr Stoeber start making twine balls?

Mr.Stoeber made the twine ball in 1953. there is your answer and i am a girl from your school pay very close attention to who i am.....


What year did Mr Stoeber stat making the twine ball?

1953


How long is the largest ball of twine in mn?

The Biggest Ball of Twine in Minnesota was created on 1989-05-24.


Where is the worlds largest ball of string?

in a meseum In Minnesota. There is also the World Second Largest Ball of Twine in Kansas and another lage ball of twine in Branson, Missouri.


What year was the twine ball first made?

1953


What is a four letter word for a ball of twine?

Yarn


How many feet in length is the worlds largest ball of twine?

The world's largest ball of twine located in Cawker City, Kansas, is approximately 41 feet in circumference.


When Jem and Scout find the ball of gray twine in the knothole what does Jem suggest they do?

Jem suggests that they not take the ball of gray twine from the knothole as it may be someone else's hiding spot or treasure. He feels that it is important to respect the mystery surrounding the knothole and leave the twine where they found it.


Do you have to pay to see the world's largest twine ball?

no its free from Cody


How do you thread a McCormick IH Forty Six baler?

THREADING THE TYING MECHANISM for a McCormick No. 46 Baler Open the door on the twine chest and place balls of twine in twine containers. There is room for 4 balls, 2 for each side. From left to right, as you look from the back of the baler, they will be referred to as balls D, C, B & A. Connect the inside end of ball "A" to the outside end of ball "B" connecting the two balls of twine in the right twine container. Connect the inside end of ball "C" to the outside end of ball "D" connecting the two balls of twine in the left twine container. If twine is taken from the wrong end of a ball, it will twist and snarl in the tying mechanism. Join the twine ends with a firm square knot. Trim the loose ends about one-half inch from the knot and you're ready to thread the tying mechanism. Make sure the needles are in their extreme rearward position. If they are not, turn the flywheel and power take-off drive by hand until the needles reach the extreme position of their rearward stroke Thread the twine from the inside of ball "B" through the grommet in the right partition and the center guide in the top of the left compartment of the twine chest. Thread the twine from the inside of ball "D" through the lower guide in the left compartment of the twine chest. Thread the twine balls "B" and "D" through the grommet in the left partition of the twine chest. Thread the twine between the pressure plates of the twine tension device and through the grommet in the bottom of the twine chest. Run the twine through the twine guide on the needle tie pipe and through the three twine guides underneath the bale chamber. The twine from the right twine container furnishes twine for the right needle and the twine from the left twine container furnishes twine for the left needle. Thread the ends of the twine through the holes of the needle head. Pull these two twine ends up through the bale chamber. Operate the baler slowly under power. Hold the twine as shown in Illust. llA (I tie it off to something near the back of the baler). Trip the clutch, and let the tying mechanism go through a cycle. Strip the single knots off the knotter hooks to complete the threading operation. Operate the tying mechanism several times at rated engine speed to be sure it is working smoothly. Hold the twine by hand each time to prevent the twine from fouling in the knotters.


Where is the the world's largest ball of twine?

I was told is was in cawker city, kansasFor many years, the world's largest twine ball has resided in Darwin, MN. It weighs 17,400 pounds, is twelve feet in diameter, and was the creation of Francis A. Johnson. He started wrapping it in March of 1950 -- four hours a day, every day. Francis lifted it with a crane to continue proper wrapping. For 39 years, this magnificent sphere evolved at Johnson's farm, and eventually moved to a circular open air shed on his front lawn.* http://www.roadsideamerica.com/story/2128