0
What sort of connectors should be used to connect a progressive scan TV and DVD player?
Wiki User
∙ 16y ago
The choice of connector is defined by the connectors on the DVD player and the TV. However, if you have a selection of connectors on each this is the preferred order to deliver the best quality: HDMI - a digital video and audio signal in a single cable (supports HD and SD) DVI - the same video signal as HDMI but you will need to add a separate audio cable as DVI carries no audio. (also supports HD, SD and other computer resolutions) Analogue component - normally three phono connectors on domestic equipment (SD only in almost all cases) RGB - May appear as 3 or 4 phono sockets or as a 15 pin D connector as found on VGA displays. (support for signals as chosen by the display manufacturer) S-Video - a small 4 pin round connector or two phonos. (SD only) Composite - A single phono and the lowest quality of all the interfaces. (SD only) Note also that in Europe, component, RGB, S-video and composite can all be carried on a scart connector which also carried audio and signalling lines. The signal interfaces remain identical regardless of whether the display is progressive or interlaced by the way. Most broadcast media is interlaced while most computer signals are progressive. The display will carry out whatever conversion is required automatically.
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
How do you connect 2.1 home theater to 5.1 onida DVD player?
The DVD player should have a simple 2 channel stereo output connectors. Use these.
How do you connect wires to car battery?
Well they should have connectors on them, if they dont then i would advise you get a mechanic to do them since you seem unfarmiliar with the process. If they do have connectors on them (they most likely do, or there would be no way to connect them) then just connect them this way: Put on the negative and screw it down, then put on the positive and do the same. Its not going to shock you if you only touch on of the connectors at a time. Also make sure, not to touch the car (like leaning on it) while you are touching the positive (red) connector or you could get shocked.
What happens when the car battery connectors connect together?
When a car battery in connected to itself (i.e. You connect jumper cables onto a battery and then connect the other two connectors to each other), you create a continual circuit with the battery and nothing else. A similar effect is when you hold a 9 Volt battery to your tongue and you feel a small but continual "zap". Imagine this effect, but much greater. Sparks will appear when the connectors are first connected. Warning: Do not do this. This will damage your car battery. The only reason you should connect a car battery through jumper cables is to connect it to another car's battery in order to "jump" a car.
How do you wire in a CD player in a ford explorer?
Buy an install kit (under $20), it has connectors that will connect the new stereo using the original connections and should come with instructions. All auto parts stores sell them, and crutchfield includes them for free when you buy a stereo from them.
How to connect a video player to your computer?
you should buy an internal TV Tuner, and then you can connect it to the AV plug, and that's it.
How can you tell that a particular ribbon cable should only be used to connect a floppy drive?
The connectors on the ends of the cable are a different size than the connectors for a standard IDE device like a Hard Drive or CD rom. You should also notice that there is a twist in the cable between two of the connectors.
What is the best portable CD player to use to connect to an MP3 player?
You cannot connect portable cd players to mp3 players and given the capacity to hold songs on mp3 players their should be no reason to do so.
When plugging the P8 and P9 power connectors into the system board which of the following is true?
the black wires of both connectors should NOT be next to each other
Where can I find out about dvi and HDMI connectors?
If you are unsure as to which connection you need for your Roku player, you should have a variety of options available to assist you. You could call the store where you purchased your player, or you could go to a Best Buy, Tiger Direct or other electronic store and they would be able to provide you with the proper dvi or HDMI connectors that you will require.
What cable do you need to connect a Blu-ray player to HDTV?
You should use an HDMI cord TMANN SHS
How do you add two players in just dance 3 for the wii?
you connect the remote then you should see player 2
Will a printer rated to use USB 3.0 work when you connect the printers USB cable into a USB 2.0 port on your computer?
It should work. If you don't have any 3.0 connectors, it should fall back to 2.0 mode.
