0
What is the size of nylon twine that is 0point051 inches in diameter?
Wiki User
∙ 12y ago
1/20th of an inch in diameter
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
Is twine made out of cotton?
The term can be applied to any thin cord, usually 2 or more strands twisted together. Twine can be cotton, hemp, nylon,or jute (which is used to make burlap).
What plant is twine made from?
The most common natural fibers (or crops) that twine is made from would include cotton, hemp, jute, and sisal. Other fibrous plants and crops can also be used (like the coir from coconuts), and twine can even be spun and made from synthetic fibers (like nylon).
What is a tennis net made out of?
A volleyball net is made out of.........wit from rope and twine
Easy diy twine rug?
Diy twine rugs are easy crafts that you can make out of twine by braiding.
Where does twine come from?
Twine is made from both plants and synthetic fibers. The two products are mixed to together to make the final twine product.
How do you use twine as a sentence?
I used twine to help my dad.
How do you get twine on FarmVille?
The collectible twine can be found when harvesting sheep on your farm.
Where is the object twine located in sims 2 castaway?
Twine is not an object or a plant. You find sisal first, then you make twine on a crafting bench.
Is twine recyclable?
If the twine is made from a natural fiber, like hemp, sisal or even cotton, then it is biodegradable.Some twine is made of plastic. This is not biodegradable.
How do you find out the diameter of a silo?
Assuming you can't get inside to measure across the silo: -- Take a long tape measure or non-stretching twine. -- Measure the distance around the silo (the circumference). -- Divide the circumference by 'pi' ... 3.142 (rounded). The answer is the diameter, within 0.02 percent.
What has the author F Twine written?
F. Twine has written: 'Low pay in Scotland'
How do you thread a McCormick IH Forty Six baler?
THREADING THE TYING MECHANISM for a McCormick No. 46 Baler Open the door on the twine chest and place balls of twine in twine containers. There is room for 4 balls, 2 for each side. From left to right, as you look from the back of the baler, they will be referred to as balls D, C, B & A. Connect the inside end of ball "A" to the outside end of ball "B" connecting the two balls of twine in the right twine container. Connect the inside end of ball "C" to the outside end of ball "D" connecting the two balls of twine in the left twine container. If twine is taken from the wrong end of a ball, it will twist and snarl in the tying mechanism. Join the twine ends with a firm square knot. Trim the loose ends about one-half inch from the knot and you're ready to thread the tying mechanism. Make sure the needles are in their extreme rearward position. If they are not, turn the flywheel and power take-off drive by hand until the needles reach the extreme position of their rearward stroke Thread the twine from the inside of ball "B" through the grommet in the right partition and the center guide in the top of the left compartment of the twine chest. Thread the twine from the inside of ball "D" through the lower guide in the left compartment of the twine chest. Thread the twine balls "B" and "D" through the grommet in the left partition of the twine chest. Thread the twine between the pressure plates of the twine tension device and through the grommet in the bottom of the twine chest. Run the twine through the twine guide on the needle tie pipe and through the three twine guides underneath the bale chamber. The twine from the right twine container furnishes twine for the right needle and the twine from the left twine container furnishes twine for the left needle. Thread the ends of the twine through the holes of the needle head. Pull these two twine ends up through the bale chamber. Operate the baler slowly under power. Hold the twine as shown in Illust. llA (I tie it off to something near the back of the baler). Trip the clutch, and let the tying mechanism go through a cycle. Strip the single knots off the knotter hooks to complete the threading operation. Operate the tying mechanism several times at rated engine speed to be sure it is working smoothly. Hold the twine by hand each time to prevent the twine from fouling in the knotters.
