0
What is the problem in using a strip of metal or any other piece of wire in place of a fuse?
Wiki User
∙ 8y ago
The fuse is made to blow at a set amperage to protect the wire from overheating. Using anything but the fuse may cause the circuit to work but could most certainly cause the wiring to overheat and burn if it is overloaded.
Wiki User
∙ 8y ago
Add your answer:
Earn +20 pts
If a piece of potassium metal is dropped in water then a vigorous reaction takes place with the formation of potassium hydroxide and hydrogen gas is evolved?
Yes, it is correct.
If a piece of metal bubbles was place in acid is that a chemical change?
No, it is not a chemical change. For example, if you put gold bubbles into any single acid, no chemical change will take place.
What are some chemical reactions?
some chemical reactions take place when a chemical is added to a metal. sometimes the chemicl turns cloudy, it may fizz or a coat of black may appear on the piece of metal. hope this helps! :)
How can you tell if a piece of iron is magnetized or neutral?
If the piece of metal is a magnet it will attract another piece of iron. You should be able to feel this attraction as the two become very close. It's magnetic field can be "seen"( that is the effect) by placing iron filings on a piece of glass and place the magnet beneath the glass. Otherwise it is not a magnet.
How can you find displacement of a metal in 50 mL of water when given the mass?
Place the piece of metal in 50mL of water and subtract the 50mL from the new volume of water. The difference will be the volume of the metal in mL and cm3. Then find the density by dividing the mass by the volume of the metal. The water must completely cover the metal in order for the displacement method of determining the volume to work.
Does a flat piece of metal have air trapped within its sides?
if you place a flat piece of metal on water will it sink or float
How do you make a 2002 Toyota Tacoma ashtray stay shut?
I had the same problem. I removed the ashtray and put a piece of duct tape on the top metal piece around the two brackets that hold it in place. Stays shut better than before. Other than that, you probably just need to buy a new one.
My passenger side window in a 1997 Saturn will not roll down?
More than likely the piece of metal holding the gears aligned is bent. You can remove the outer panel and hammer the metal piece back in place.
How would I fix a front spring problem on a 97 Lincoln continental after I found a black horseshoeu shape piece of metal by passenger side on garage floor.?
that horseshoe shaped metal is to hold the air cylinoid into the air spring. check the air cylinoid make sure it is in place. that horseshoe shaped metal is to hold the air cylinoid into the air spring. check the air cylinoid make sure it is in place.
Can metal absorb solar energy?
I suggest you place a piece of metal in the sunlight. If it gets warm or hot, that means that yes, it absorbed at least part of the incoming energy.
What is a woodriff key?
a woodruff key is a small piece of metal that holds something in place to keep it from moving..like a pulley
Where to place a wireless router?
It's better to put it on open place far from metal walls and grids. Usual walls are not a problem for signal.
How do you drill a hole in a bathtub?
Menards sells plugs that you put through the hole and on the back side is a threaded piece and you put a nut on the threaded piece and it holds it in place. It has a gasket so it wont leak. On the front its a round trim piece that looks like metal.
What is the plastic piece hanging under 2002 Mercury Villager?
You are probably referring to the piece under the front bumper. That is a stone shield. It is held in place by several plastic rivets and metal screws.
Filler what can you use for brazing holes in sheet metal?
If the hole is very small the material you are brazing with should fill it. A small piece sheet metal can be brazed in place to cover larger holes.
How do you install an alto sax reed?
If you take the round metal piece off the top of the mouth piece by loosening the screws, and place the reed next to the mouth piece so the flat side is next to the mouth piece. Then, line up the curved top of the reed with the curved top of the saxophone, so you can only see a tiny bit of the mouthpiece. Put on the round metal piece again and tighten it using the screws. There you have it!!
What is a pin back button?
This is not a button used for fastening a garment. It is made of metal. It attached to your clothing by means of a pin on the back, rather like a safety pin. A pin back button usually has a witty saying, political slogan, or picture on its face. (Other buttons may have a tie-tack clasp: a straight piece of metal that goes through your clothing and has a separate metal piece you put on the back to hold it in place, kind of like a pierced earring.)
