answersLogoWhite

0

How do you get rid of calcium depositis on pool tile?

Updated: 9/28/2023
User Avatar

SurfaceRenewal

Lvl 1
14y ago

Best Answer

I'm guessing that you have a salt water pool. Sometimes water will evaporate and leave behind salt crystals. Usually the problem is calcium or other hard water minerals that get deposited at the water line and anywhere water splashes on the tile. If you do have "salt" it will probably just brush off. If however it is calcium it can be removed with an acid (like Biodex 300) while it is just a light film. If it has accumulated enough to form a crust you will most likely need a professional. There are three methods to remove it. Some use wire wheels and grinders others use sand or glass bead blasting. The newest method, and least damaging to tile is water blasting with magnesium sulfate.

User Avatar

Wiki User

16y ago
This answer is:
User Avatar
More answers
User Avatar

Wiki User

15y ago

Are you sure it's chlorine? If so it should rinse off with water. If on the other hand you are talking about a white film or deposit at the water line it is most likely calcium or another hard water deposit. A film can usually be removed with an acid product (I prefer Bio Dex 300) be very careful to follow the instructions, it is very dangerous. If calcium is allowed to build up too long it forms a thick crust almost impossible to get rid of. You may try a pumice stone (follow instr or you can damage the tile. Failing that you'll need to call a professional. One process uses glass beads to blast the residue off. The newest process uses high pressure water and a soft media to remove the calcium ******************************************************************** People using acid need to be very careful as to you can easily ruin more than just your tile. As far a glass beads goes you would be better off getting a piece of coarse grit sand paper and scuff away because you'd get the same result of having someone bead blast it; but on more of the harder surfaces like fake rock, stone, flagstone, etc glass beads would work well. But the water blast setup works by far awesome. Maxxstrip is the media in term "soft abrasive" that would be used it safely removes build-up on tile and even leaves a shine to tile. Here is a link to the setup: http://www.universalminerals.com/maxxclean.shtml

This answer is:
User Avatar

User Avatar

Wiki User

16y ago

A lot of people will use a scouring pad with a strong detergent. this is not necisarily good for the chemical composition of pool water. it is wisest to seek advice on this from your local pool shop as they will carry exactly what you need.

This answer is:
User Avatar

User Avatar

Wiki User

15y ago

You can DIY if it is still just a light film. I use a product called Bio Dex 300 FOLLOW the instructions or you could damage the tile or worse, hurt yourself. If the deposit has gotten to the thick baked on stage you probably need a professional. The old method uses air blasting and glass beads. A newer method only available in the past 4 years uses a power washer and a mineral salt to clean. Do your homework before hiring someone.

Depending on how many hard water stains there are on the pool, you could try a natural method. White vinegar has been proven to work time and again and is non-toxic, see below for a proven step-by-step technique:

Natural Formula to Use:

A mixture of baking soda & white vinegar to make a paste

Method to Use:

1. Make up the mixture of water and baking soda

2. Apply to stain and let dry on the tile

3. Scrub stains with a brush or sponge

4. Rinse thoroughly with water to remove all residue, reapply if necessary

This answer is:
User Avatar

User Avatar

Wiki User

15y ago

You didn't say what you are trying to remove. If you have mold, algae you could try using biodex 300, (or a similar prodict) a very strong acid. BE CAREFUL. If it's a mineral deposit (usually calcium) Biodex will also work as long as the deposit is just a film. If it's been around awhile and is thicker you can try a pumice. Be careful not to scratch the tiles. If it's worse you will need to hire a professional. There are basically three methods that work. They may use a grinder or sander to remove the deposit (easily damages the tile) they may use glass bead blasting ( also easily damages tile) The newest method is to use a power washer and mineral salts. (won't damage tiles) The mineral used is too soft to damage the glaze. Despite claims from bead blasters it won't knock the tiles off either. If the tiles are loose enough to fall off you have a more serious problem.

This answer is:
User Avatar

User Avatar

Wiki User

13y ago

Chlorine residue? Chlorine is a gas that dissipates automatically over the course of many hours - that's why you have to add it every day. There is no "residue". To reduce the chlorine content of pool water, merely wait 24 hours - 48 if neccesary.

This answer is:
User Avatar

User Avatar

Wiki User

14y ago

Try CLR ( calcium lime rust ) remover, it is available at most supermarkets and home improvement stores.

This answer is:
User Avatar

User Avatar

Wiki User

14y ago

The only way I would sugest to do this is to bead blast it away by calling Surface Renewal (949)269-3122

This answer is:
User Avatar

User Avatar

Wiki User

14y ago

The best way is to bead blast it away. Surface Renewal does this safely.(949)269-3122

This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you get rid of calcium depositis on pool tile?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

They are afraid to bead blast the tile in my spa - how do you get rid of calcium on grout and tile?

Muratic acid, diluted of course; but you will have to reseal the grout. You can buy it at any hardware store.


When you drain your pebble tec pool and power wash it how can you get rid of water line deposits?

More than likely the white ring on the pool is calcium and it will need to be bead blasted, check the phne book to find a tile saver company. Gary - the water line is where you put it. add water to raise, lower to lower. to remove black lines (caused by human sweat and oils) use a surface cleaner and a tile brush available at any pool supply store I cleaned the calcium water line on my pebbletec pool with a wire brush, removed the calcium and didn't remove or damage the pebbletec surface.


How do you get rid of calcium precipitation in a salt pool?

Use something acidic i.e. acetic acid (vinegar)


How do you get rid of calcium deposits from an in ground swimming pool?

You can try Biodex 300 if the mineral deposit is just a film (CAUTION IT'S DANGEROUS). If it is thicker you can try a pumice stone (CAUTION MAY SCRATCH TILE). You can hire someone to blast with glasss beads (IT WILL DAMAGE THE TILE), or to dry ice blast (IT IS NOT LIKELY TO DAMAGE THE TIME). You can contract someone to clean with natural mineral salts (SAFE) To find someone who uses mineral salts, search on the internet for "pool tile cleaning magnesium sulfate".


What is the ingredients of damp rid?

Calcium Chloride. You can purchase it at pool supply stores for less than the brand-name refills.


What is the best way to get rid of rough spot in pool?

What is the best way to get rid of rough spots on pool steps??


If RID master fails what happens?

The RID master will allocate the pool of RIDs to the DC, So we can create the objects without RID master. When this RID pool exhausted we can't create object.


How do you get rid of cotton from your pool?

I have to clean it


How do you get rid of the smell from liquid incence from tile grouted floor?

Try Bleach


How long will it take to get rid of the calcium build-up in your heart?

The calcium is in blood and in bones as a reserve also. There is no calcium in your heart. The calcium is in blood and in bones as a reserve also. There is no calcium in your heart.


How do you get rid of calcium in well water?

You use the appropriate filter for it.


How do you get rid of pool black spot?

Bleach or Clorox.