0
The term is 'alternating voltage', not 'alternate voltage'. For an a.c. voltage or current, the average value is taken over half its wavelength because, over a complete wavelength it is, of course, zero. For a sine wave, the average value (over half a wavelength) is 0.637 Vmax or 0.637 Imax.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What mathematical formulas is used to find the average value voltage for an ac voltage?
The RMS value of an AC voltage is VRMS = VPEAK / sqrt(2), where VPEAK = the voltage peak to neutral.AnswerThe average value of a sinusoidal a.c. voltage is zero.
Does digital voltmeter measures rms voltage or peak to peak voltage or average?
Yes, most DMM are ''average responding", giving accurate rms reading if the ac voltage signal is a pure sine wave. They measure the average of the absolute value of ac voltage and are calibrated so that reading are corrected to that of the rms value of a sine wave.Error occur if harmonic are present.
Why is average voltage of full wave rectified voltage different from the rms value of an equivalent ac waveform?
the number u are seeking is 0.639
Why you take 2Vm peak inverse voltage for full wave rectifier?
When the AC waveform goes to one peak, the capacitor that follows the diode is charged to that peak value. When the AC waveform goes to the other peak, the same diode is reverse biased between the alternate peak value and the charged value of the capacitor. This differential voltage is two times peak voltage.
What is transient voltage?
A transient voltage is a time varying voltage value. Transient says that the voltage value changes, especially from a steady state, to a new value, then back again.
What mathematical formulas is used to find the average value voltage for an ac voltage?
The RMS value of an AC voltage is VRMS = VPEAK / sqrt(2), where VPEAK = the voltage peak to neutral.AnswerThe average value of a sinusoidal a.c. voltage is zero.
How voltage doubler works?
The voltage doubler works by charging alternate capacitors on alternate half-cycles. Since the capacitors are in series, the voltage doubles.
What is RMS Peak value and average value?
RMS is used to determine the average power in an alternating current. Since the voltage in an A/C system oscillates between + and -, the actual average is zero. The RMS or "nominal" voltage is defined as the square root of the average value of the square of the current, and is about 70.7% of the peak value.************************************************************The r.m.s. value of an alternating current or voltage is the value of direct current or voltage which produces the same heating effect.Fo a sine wave, the r.m.s. value is 0.707 x the peak value.The average value is different; for a sine wave it is 0.636 x the peak value.
What is the form factor of a half wave rectifier?
It is defined as the ratio of RMS value of output voltage to the average value of the out put voltage.
What is the relationship between peak rms and average values of an ac voltage?
Peak voltage of an AC voltage is the value at its highest or lowest point.RMS (Root Mean Square) voltage of an AC voltage is a mathematical derivation involving the square root of the average value of the squares of samples of the voltage as the sample interval approaches zero.Average voltage is simply that - the average or mean voltage.For a true sine wave, RMS and average are equivalent, but they are not equivalent when the wave is distorted, or has some other shape such as triangular.RMS is the best way to measure an AC voltage, as it gives you a true reading of the amount of power that the voltage can deliver.One issue with non-RMS AC meters is that they typically measure the rectified, filtered peak value and then compensate by dividing by 1.4. This is not correct unless the voltage is a sine wave.AnswerThe peak value of an a.c. voltage or current is the amplitude of that voltage or current waveform -i.e. the maximum value of voltage or current in either the positive or the negative sense.The root-mean-square (rms) value of an a.c. voltage or current. For a sinusoidal waveform, the rms value is 0.707 times the peak value (amplitude). A.C. voltages or currents are always quoted in rms values unless otherwise specified.The average value of an a.c. voltage or current is zero over one complete cycle so, when used, it applies only over one half cycle. Therefore, the average value for one-half cycle of a sine wave is 0.637 times the peak value. Average values are of little relevance to a.c. calculations.
What bipolar encoding scheme uses either positive or negative voltage values to represent a 1 value?
Alternate Mark Inversion (AMI)
The effective value of ac voltage is calculated as?
EFFECTIVE HOW ABOUT AVERAGE .639 of peak.AnswerThe 'effective' value of an a.c. voltage (or current) is the same as its 'root-mean-square' (r.m.s.) voltage which, for a sinusoidal waveform, is 0.707 Umax.The 'average' value of an a.c. voltage (or current) is zero over a complete cycle, or 0.639 Umax, over half a cycle (usually applied to rectified waveforms).
What is different between rmsvoltage and average voltage?
The RMS value of a sinusoidal voltage is 2/pi x (the peak voltage).The time average of a sinusoidal voltage is 1/sqrt(2) x (the peak voltage).So I guess the difference is ( 2/pi minus 1/sqrt(2) ) x (peak voltage) = 0.07 of the peak voltage. (rounded)The significance is:The RMS value used to be called the "heating value". It's the value of the DC thatyou'd have to pass through a toaster coil to produce the same heat as this AC.But the heating effect at every instant is not proportional to the voltage. It's proportionalto (the voltage)2. So the heating effect is stronger near the top of the waveform thanyou'd expect, and it's stronger than a DC at the average value.
Does digital voltmeter measures rms voltage or peak to peak voltage or average?
Yes, most DMM are ''average responding", giving accurate rms reading if the ac voltage signal is a pure sine wave. They measure the average of the absolute value of ac voltage and are calibrated so that reading are corrected to that of the rms value of a sine wave.Error occur if harmonic are present.
Why is average voltage of full wave rectified voltage different from the rms value of an equivalent ac waveform?
the number u are seeking is 0.639
Why different frequencies has same average value and RMS value?
Voltage and frequency are independent quantities.AnswerBecause the r.m.s. value is dependent on the shape of the waveform, not its frequency. The average value of any symmetrical waveform is zero and is independent of frequency.
What is the conversion for rms voltage to mean voltage?
For an alternating voltage, the simple mean over a cycle would be zero. 'RMS' means 'root mean square', and is defined as the square root of the mean value of the square of the voltage, taken over a cycle. Thus whether the voltage is + or - , as it is in alternate half cycles, the value of its square is always positive, giving a real number for the square root. In fact the RMS value of voltage produces an RMS current which dissipates power at the same rate as a DC current of the same value. To find the RMS value of a sine wave with no DC offset, divide the peak value of the sine wave by square root of 2. **************************************************** Since the r.m.s. value of a sine wave is 1.414Vpk, and the mean voltage of a sine wave is 1.57Vpk, then, starting with the r.m.s. value: Vmean = (Vr.m.s. x 1.414) ÷ 1.57
