0
The IH Mccormick 50, 55, and 45 balers all had twine boxes on the sides of chute on the rear of the baler.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
How do you thread a McCormick IH Forty Six baler?
THREADING THE TYING MECHANISM for a McCormick No. 46 Baler Open the door on the twine chest and place balls of twine in twine containers. There is room for 4 balls, 2 for each side. From left to right, as you look from the back of the baler, they will be referred to as balls D, C, B & A. Connect the inside end of ball "A" to the outside end of ball "B" connecting the two balls of twine in the right twine container. Connect the inside end of ball "C" to the outside end of ball "D" connecting the two balls of twine in the left twine container. If twine is taken from the wrong end of a ball, it will twist and snarl in the tying mechanism. Join the twine ends with a firm square knot. Trim the loose ends about one-half inch from the knot and you're ready to thread the tying mechanism. Make sure the needles are in their extreme rearward position. If they are not, turn the flywheel and power take-off drive by hand until the needles reach the extreme position of their rearward stroke Thread the twine from the inside of ball "B" through the grommet in the right partition and the center guide in the top of the left compartment of the twine chest. Thread the twine from the inside of ball "D" through the lower guide in the left compartment of the twine chest. Thread the twine balls "B" and "D" through the grommet in the left partition of the twine chest. Thread the twine between the pressure plates of the twine tension device and through the grommet in the bottom of the twine chest. Run the twine through the twine guide on the needle tie pipe and through the three twine guides underneath the bale chamber. The twine from the right twine container furnishes twine for the right needle and the twine from the left twine container furnishes twine for the left needle. Thread the ends of the twine through the holes of the needle head. Pull these two twine ends up through the bale chamber. Operate the baler slowly under power. Hold the twine as shown in Illust. llA (I tie it off to something near the back of the baler). Trip the clutch, and let the tying mechanism go through a cycle. Strip the single knots off the knotter hooks to complete the threading operation. Operate the tying mechanism several times at rated engine speed to be sure it is working smoothly. Hold the twine by hand each time to prevent the twine from fouling in the knotters.
Can you sharpen cutter blades for a McCormick IH 46 baler or where can you find them?
yes you can. new replacent # 668961r21
Who is the producer of a baler?
John Deere, Case IH/Agritrac, New Holland and Massey are the main companies that produce balers, primarily small square, large square, and large round. The large square baler is the most expensive to purchase. SINOBALER is a specialized baler manufacture based in China. Balers manufactured include cardboard baler, textile baler, bottle baler, tyre baler, fiber baler as well as various kinds of vertical balers and horizontal balers.
Who won silver in in the winter Olympics snowboading in 2010?
hi hi ihi ihi hihihihih ih ih ihi ih hi ih ih ih ih ih i ihi ihhi h ih ihi h ihih i hi ih hi ih ih ihi h ih ihi peace
Where is Hydraulic pump on a 1086 IH tractor?
Pump for brakes steering and TA under battery box ,left side. 3 point hitch and remotes is under left brake in front of axle
Where is the Ih Collectors Lone Star Chapter 25 in Richardson Texas located?
The address of the IH Collectors Lone Star Chapter #25 is: P. O. Box 986 Henderson, Texas 75653
ih+ ih 3?
that technically doesn't have a real answer but my guess is ih 4
Where can you find decals for your ih 574 tractor?
Try a Case-IH dealership.
Retail price of a Emerson 45rpm phonograph?
you love it ey eh eh eh uh uh uh uh ih ih ih
Where is university Texas San Antonio located?
The Main Campus is near 1604 and IH-10 on San Antonio's northwest side.
Where and when did IH tractors originate?
International Harvester (IH) was founded in 1847 as the McCormick Harvesting Machine Company in Chicago. The first IH tractor was released in 1926.
How old is John Wayne County?
hi hi hi hi hih ih i ih i ih hi
