You have to pull a new wire. There is no way to do it with the existing wire, at least no way you should do it and be in code.
You can,t. You need to use a three way switch.
See discuss question button below.
wire each switch to each light...
A proper "3-way switch" would be capable of being switched to 3 different positions and could have one, two or more poles. Each pole could be either single- or double-throw."How does a single pole switch differ from a three way?" is a trick question often asked to catch-out new trainee electricians because the common but mis-named "three-way switch" is actually a single pole, double throw switch, i.e. it is only a 2-way switch, not a 3-way switch.A pair of "3-terminal, single pole, double throw" switches are often used to hook-up two separate light switches to control one light or one set of lights.The same answer put in a different wayDespite the fact that the name "3-way switch" is often used to describe it, if it is of the type that has just one pole that can only be physically switched 2 ways, the name "3-way switch" is quite wrong for that particular switch. A "3-terminal, single pole, double throw" switch" is a more accurate description for it.
Not usually, The light would have had to been wired with a three wire from the switch to the fan. One circuit to control the fan and the other switch to control the light. If this is your situation then all you will have to do is change the light switch to a timer and that will do what you want.
Yes. A center point switches to either one side of the switch or the other. Just use the center and either of the other contacts. Leave one switch terminal unconnected. If you can't figure out which is the center switch point you have a 2 in 3 chance of getting it right and if the switch doesn't work you picked the one wrong choice. It will still be a single pole but a 3 way will work. I believe you should use the connections that are on the same side. The incoming and the 3 way on the same side. Does that make sense? <<>> Yes you can, just make the connection between the two screws that are of different colours. When you re-install the switch make sure that the positioning of the switch is, toggle up for on and toggle down for off as there is no dot on the toggle handle to let you know the on position.
The light is wired the same as any voltage fixture. Bring the source voltage to the fixture and connect it to the two fixture wires. If you want to control the off-on of the fixture take the source voltage to a switch first and then out of the switch to the light fixture.
wire each switch to each light...
I can not understand your question.
A proper "3-way switch" would be capable of being switched to 3 different positions and could have one, two or more poles. Each pole could be either single- or double-throw."How does a single pole switch differ from a three way?" is a trick question often asked to catch-out new trainee electricians because the common but mis-named "three-way switch" is actually a single pole, double throw switch, i.e. it is only a 2-way switch, not a 3-way switch.A pair of "3-terminal, single pole, double throw" switches are often used to hook-up two separate light switches to control one light or one set of lights.The same answer put in a different wayDespite the fact that the name "3-way switch" is often used to describe it, if it is of the type that has just one pole that can only be physically switched 2 ways, the name "3-way switch" is quite wrong for that particular switch. A "3-terminal, single pole, double throw" switch" is a more accurate description for it.
there are a couple of settings you need to turn the light off at the light switch. it will then only come on if a door is open any time you want to use it ,you can switch it on or off at the light switch you can turn it off at the light switch on the dash it will then come on when you open a door any other time you want to use the cargo light you can switch it on or off at the light switch
There is a selector switch for the barrel you want. Not both barrels at the same time
You will want to replace a brake light switch on a VW Polo professionally. You do not want to make a bigger situation than you already have. A mechanic will do the job correctly.
A good quality, proper specification American made light switch is so inexpensive, I can't understand why you would want to use a foreign light switch. Des Perado
Could be the dash light switch is turned off.
There is insufficient information to answer your question since "old light switch" is open for interpretation. However, if you want to find the push button type light switch, search on the internet for "vintage electrical parts" and you should be able to find several suppliers.
This is simple. First the wire coming from the power supply go to the switch. Then it goes to the first , the second and the third light. Since the switch comes first all three light will be controlled by that one switch.
Because they want you to get FAT!
Not usually, The light would have had to been wired with a three wire from the switch to the fan. One circuit to control the fan and the other switch to control the light. If this is your situation then all you will have to do is change the light switch to a timer and that will do what you want.