Instructions for skyscan atomic clock model 86742?

Answer 1

SkyScan Model 31981B TO START THE CLOCK:

1. Insert 2 AAA batteries with proper polarity (+) and (-)as indicated In the battery compartment.

2. The LCD goes to default time and calendar 12:00:00AM (time) and 1-1 (Jan 1 2003).

The alarm time is 6:00 AM.

Default time zone is PST, default temp. readout Is degree F.

3 The clock takes the temperature reading immediately then starts to search for the WWVB signal. Remarks: If you immediately manually set the time / alarm time / calendar the clock will slop its initial reception of the WWVB signet. It will resume to the WWVB reception automatically when the clock exits SET mode and no other button is pressed for 5 seconds.

TO SELECT THE TIME ZONE:

1. Press TIME ZONE button once, the LCD shows the time zone (the default time zone is PST).

2- Press + or - - to set the time zone (PST>MST>CST>EST)

3. Press the TIME ZONE or SET button to go back to the time display or it will automatically go back to the time display in 5 seconds.

TO SET TIME, CALENDAR, 12/24HR AND C/F:

1. Press the SET button once to set the Year: digits show '2003" and blink. Press + or - - to set the year.

2. Press the SET button again to set the Date : small digits show " 1 - 1" (i.e. Jan 1st) and blink. Press + or - - to set the date. Press and hold + or - will increase the increment or decrement at a faster rate.

3. Press the SET button again to set the Time : large digits in HR : MIN will show and blink.

Press + or - to set the clock to the current time. Press and hold + or - will increase increment or decrement at a faster rate.

4. Press the SET button again to set 12 / 24 HR readout. Upper LCD shows "l2Hr" and blink.

Press + or - to choose 12HR or 24 HR time display format.

5. Press the SET button again to select C/Freadout: the temperature readout (i.e. 68F) will blink. Press + or - to choose readout (i.e. 68F or 20C ). The default readout is In degree F.

6. Press the SET button again to exit the setting mode and return to the normal display. Or it will automatically return in 5 seconds. **Special attention for usage in Arizona and Indiana.**

Part of Arizona and Indiana do not have Daylight Saving Time (DST).

Please slide the DST switch inside the battery compartment to OFF if the clock is used in these states.

TO SET ALARM TIME ;

1. To read your alarm time: press + or - once, the lower Month and Date digits will change to alarm time digits.

2. To set the alarm time: press + or - again, the alarm digits will blink, Press + or - - to set your alarm time. Press and hold + or - will increase the increment or decrement at a faster rate..

3. Alter you set the alarm, the clock will go back to the normal display automatically in 5 seconds.

TO TURN ON/OFF THE ALARM:

1. To use snooze alarm

Press the SNOOZE / AL ON/0FF button until SNZ and (((o))) show on lower LCD.

When the alarm beeps, press SNOOZE / LIGHT bar. The alarm will Sound again when the snooze period

is over. (See "To Program the Snooze Alarm " below)

When the alarm beeps, press any key at the front to stop the alarm. The snooze alarm will turn on the following day at the same time.

2. To turn on alarm

Press the SNOOZE /AL ON/OFF button until (((o))) shows on lower LCD.

When the alarm beeps, press SNOOZE / LIGHT. The alarm will turn on the following day at the same time.

3. To disable the alarm permanently:

Press the SNOOZE / AL ON / 0FFbutton until the SNZ and (((o))) clear from the lower LCD.

TO PROGRAM THE SNOOZE ALARM:

1. Press and hold the SNOOZE I LIGHT bar for 3-4 seconds. The small display will blink and show 05 (minutes) the default snooze duration. Press + or - to set the snooze duration from 5 minutes to 60 minutes.

Note: The minimum snooze duration is 5 minutes.

2. Press the SNOOZE I LIGHT bar once to go back to the normal display or the clock will auto exit if no further buttons are pressed after 5 seconds.

Answer 2

Hold down the alarm on/off button on the back of the clock for a few seconds until the hour flashes. Using the adjust button, set the hour. Then hold the alarm button down again to set the rest of the clock continuing the procedure for each category.

To set the alarm use the mode button to go to alarm time. Press the alarm on/off until the hour flashes. Use the adjust key to change the hour then press the adjust key to change the minutes. The mode button saves it all.

Getting the right time zone should work automatically. If not set the clock on a window sill facing west and wait.

Answer 3

How To Set Your Time Zone

Time Zones around the world are identified by how many hours they are off-set from Greenwich Mean Time. US time zones are 5 to 9 hours behind Greenwich Mean Time and are identified as:

Eastern -5

Central -6

Mountain -7

Pacific -8

Alaska -9

Your SkyScan model 31983 is pre-set to Pacific Time. To set your clock to your time press and hold the mode button for 2 seconds. The off-set hours will appear and blink in the clock window. Press the up or down button to designate your time zone. Press the alarm button to exit time zone setting mode.

How To Set 12 hour or 24 hour Display

Press and hold the mode button to 2 seconds. The off-set time will appear. Press the mode button again. The 12hr or 24hr display will blink. Press the up or down button to toggle back and forth between 12 hr and 24 hr display mode. Press the alarm button to exit 12hr or 24 hr setting mode.

How To Manually Set the Time and Date and Language.

Your SkyScan clock is designed to automatically set itself using the radio signal originating from the US Atomic Clock. Please allow your clock up to 72 hours to synchronize with this signal.

Should the need or desire to manually set the clock arise, follow these instructions:

1. Press and hold the mode button for 2 seconds. The time zone off-set hours will begin to blink.
2. Press the mode button again. The 12hr 24 hr mode will blink.
3. Press the mode button again. The hour will begin to blink. If in 12hr mode the PM indicator will show afternoon hours. The PM indicator will not show for morning hours. Press the up or down button to reach the desired hour.
4. Press the mode button again. The minutes will begin to blink. Press the up or down button to reach the desired minutes.
5. Press the mode button again. The year will begin to blink. Press the up or down button the reach the desired year.
6. Press the mode button again. The month will begin to blink. Press the up or down button to reach the desired month.
7. Press the mode button again. The date will begin to blink. Press the up or down button to reach the desired date.
8. Press the mode button again. A letter indicating the language will begin to blink. Use the up or down button to change the language used to show the weekday.

E - English

D - German

F - French

I - Italian

S - Spanish

1. Press the mode button again to exit setting mode.

NOTE: You may press the alarm button anytime to exit the setting mode.

How To Set the Alarm (s)

This unit is ……..

To set the weekday and/or single alarms:

1. Press the alarm button. The weekday alarm icon will appear.
2. Press and hold the alarm button for 2 seconds to enter the setting mode. The hour will begin to blink. Press the up or down button to reach the desired hour. In 12hr mode the PM indicator will light for afternoon hours.
3. Press the alarm button again. The minute will begin to blink. Press the up or down arrow to reach the desired minute. Press the alarm button again to exit the weekday alarm setting mode.
4. Press the alarm button again. The single alarm icon will appear.
5. Press and hold the alarm button for 2 seconds to enter the setting mode. The hour will begin to blink. Press the up or down button to reach the desired hour. In 12hr mode the PM indicator will light for afternoon hours.
6. Press the alarm button again. The minute will begin to blink. Press the up or down arrow to reach the desired minute. Press the alarm button again to exit the single alarm setting mode.

To activate or deactivate the alarms:

1. Press the alarm button until either the weekday or single alarm icon appears.
2. Press the up or down button to activate or deactivate the chosen alarm. If dashes show instead of time, the alarm has been deactivated.

Answer 4

The information can be found here: http://skyscan.info/content/index.php?option=com_content&task=view&id=29&Itemid=40

Answer 5

You can find instructions for the SkyScan Atomic Clock model 28600 online at places like the SkyScan Atomic Clock website. This website offers a free download option for the manual.

Answer 6

Look at the web site for the Atomic Clocks Store. There you can search by the clock's name and model number.

Answer 7

http://skyscan.info/content/index.php?option=com_content&task=view&id=38&Itemid=40

Answer 8

I need to buy a new sensor for my model 87310 billb8069@gmail.com

Answer 9

No

Answer 10

how to reset time and date