Of course the answer is yes if use with our energy saving dimmer.
Our energy saving dimmer is the only one can dim CFL,LED,T4,T5,T8,ceiling lamps,halogen lamp,quartz lamp etc. in the world.
Our dimmer can apply to any brand of light source and lighting fixture.For example,our dimmer can dim the CFL of PHILIPs�ORSAM�GE etc.and this will not affect the performance and lifetime of lamp.Furthermore, dimming increases lifetime of lamp and saves energy because less electrical wattage is used. For example, a lamp that is dimmed by 25 percent uses about 20 percent less electricity and the lamp's life is increased four times.
Pls visit http: //v. blog. sohu.com/u/vw/3839082 to see the demonstration.
or send your inquiry to jennixiao [at ] @gmail.com,i would like to help you.
+++
Does dimming a light actually reduce the power consumption? Most of these use variable regulators, so where does the "lost" part of the a. c. waveform from the mains go if not into heat in the regulator itself?
Many dimming technologies have been used over the years, including motorized rheostats, autotransformers, magnetic amplifiers, vacuum tubes, and vats of salt water. Some of the ones that are more commercially successful are listed below.
Rheostats:
In the early 1900's, a large variable resistor called a rheostat was used to reduce the energy to the lightbulb. This resulted in high power dissipation in the 'dimmer' and no energy savings: all power was either heating the light or heating the dimmer.
Solid-state Dimmers:
Some dimmers use solid-state devices such as triacs to turn the power applied to the load on and off 120 times per second. By varying the time the power is off, the light gets brighter and dimmer. However, triac dimmers distort the sinusoidal AC waveform so cannot be used to drive motors. Triac dimmers also switch off 120 times a second while high current is flowing, creating noise (audible and electronic) and requiring filtering.
Newer solid state dimmers use IGBT devices that switch on slowly and off at zero current, reducing noise but generating more heat.
Sine wave solid state dimmers are also avaialble, that produce true sine wave output at any voltage output.
Modern dimmers using triacs are >99% efficient, however there is still some small dissipation in the triac. This causes the dimmer to become slightly warm to the touch.
Some dimmers are included in the lighting instrument, and move a mechanical shutter in front of the light source, or electronically dim the source (as with LEDs).
because of voltage
the dimmer should have a rating on it in Watts. dimmers are not suitable for low energy lamps though
120 volt xenon bulbs are fully dimmable just like a regular incandescent bulbs, using regular old 120 volt dimmer switches.
Compact fluorescent bulbs used to be all or nothing. They couldn't be dimmed. Most cfl lamps (bulbs) are this kind. However, special cfl bulbs are now being marketed, at a higher price, that can be dimmed by a normal dimmer switch previously used for incandescent bulbs. However, not all dimmer switches work with these newer dimmable cfl lamps.
Nothing . . . obviously.
Neither. Connecting lamps in parallel subjects each lamp to its rated voltage, so they will each operate at their rated power (therefore brightness).
Bulbs in a parallel circuit draw the same amount of current, so each will display the same brightness. Bulbs in a series circuit share the current so all bulbs will appear dimmer.
When light bulbs are connected in series circuits, they will get dimmer whenever a bulb is added. This is because the current is shared between all of the bulbs equally.AnswerLamps only operate at their rated power when subjected to their rated voltage. If you connect lamps in series, each lamp will be subject to a lower voltage, so they will not operate at their rated power and, so, will be dimmer. The more powerful lamps will actually glow less than the less-powerful lamps because their resistance is lower and the voltage drop across them will also be lower than the voltage drop across the less powerful lamps.
I have but if dimmer is on low the light fixture sometimes "hums", can be anoying It also shortens the bulb life, significantly in some cases. But their are also CFL bulbs built to be used with a dimmer switch that avoid these problems.Another AnswerYou should only use CFLs specifically-designed to be used with dimmers in circuits controlled by dimmer switches. There is a proven danger of fire hazard when ordinary CFLs are controlled by dimmer switches and, so, this should NEVER be done.
yes
because of voltage
Not necessarily. They can be brighter, or less bright. Both the energy saving light bulbs and the old-fasioned incandescent light bulbs come in different powers.
No yoiu can not
If you are comparing parallel vs series circuits, light bulbs produce more light in parallel circuits.
There are two types of modern bulbs, CFL and LED and they are available in various wattages. While more expensive initially, there is tremendous energy savings over the extended life span.
the dimmer should have a rating on it in Watts. dimmers are not suitable for low energy lamps though
Do nothing. But in a parallel circuit, all the bulbs will get dimmer.