How do you reset oil change light in a Chevy venture?
Try turning the key to "on" position without starting vehicle Push accelerator to the floor 6 times Shut off key Start vehicle
3 people found this useful
ignition on - engine off - floor the gas pedal 3 times. That's it!
To reset the oil light, put the key in the ignition and turn to accessory setting (but do not start the car) Push the English/Metric button twice and then push and hold the "G…auges" button. The "Change Oil" light will flash for about 15-20 seconds and then go out. Release the button and turn key off. When you turn the key back on, the light should be out. If it is not, repeat the above steps.
turn the key to "on", just shy of engaging the starter. push the gas pedal to the floor fully 3 times. If this doesn't cause light to flash and reset turn off key and try agai…n except push gas pedal 4 times. AP Anc AK If that doesn't work; With the key off, push and hold in the odometer button, depress the break pedal 10 times then release the odometer button. Problem solved....
The change oil light comes on and frequently on my 2001 Venture. The "OIL Change doc" at our local garage says it is a problem with the oil screen. It gets gunked up and needs… to be cleaned or replaced to stop this message. It could also cause overheating in the van if left unattended. Good luck! This information can be found in your owner's manual. Don't have one get one. Try Dealer, Salvage Yard, E-Bay, or do a Google search. Many sites sell owner's manuals. __________________ At www.chevrolet.com you can sign up and see your owner's manual free online. Here is what it says about resetting that light: 6-16 How to Reset the Change Engine Oil Message The GM Oil Life System_ calculates when to change your engine oil and filter based on vehicle use. Anytime your oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where you change your oil prior to a change engine oil message being turned on, reset the system. 1. With the ignition key in RUN but the engine off, repeatedly push the trip/reset button until OIL is displayed on the Driver Information Center. 2. When OIL is displayed, push and hold the trip/reset button for five seconds. The number will disappear and be replaced by 100 (indicating 100% oil life remaining). 3. Turn the key to OFF. If the change engine oil message comes back on, the engine oil life monitor has not reset. Repeat the procedure.
Answer . turn the car to acessary or trun the car on with out turning the egine over and then hold the trip oil located by the by were it tell the millage on the car the c…hange oil will then flash
Answer . \nNot sure about your Venture, but Chevy trucks are:\nTurn ignition to run (do not start engine).\nPress gas pedal completely to the floor three times in five sec…onds.\nWait 10 seconds (if you have one of the oil life monitor screens, watch for it to blink.)\nTurn ignition switch off.\nStart the vehicle.
Answer . \nturn the key to the on position engine not running step on gas pedal to the floor three times and wait for light to flash and go out and its reset
Answer . turn on ignition switch and press and release the accellerator three times slowly within 5 seconds. turn if switch and recheck. if fails the first try it again.
turn the ignition key to the on position (but do not start the vehicle) .Then push the trip odometer button a few times until the word oil appears on the screen. There will be… a number next to the word oil. Hold the button in until the number 100 appears next to the word oil and then your good to go
DO you own the vehicle owners manual?. This procedure is inside the owners manual. ( page 6-15). But this is the steps (as listed in the owners manual)---. HOW TO RESET THE… CHANGE ENGINE OIL MESSAGE. 1. with the ignition key in run but the engine off, fully push and release the accelerator pedal slowly three to five times within five second.. 2. turn the key to off.. (if the CHANGE ENGINE OIL) message comes back on, the engine oil life monitor has not reset - repeat the procedure...
Turn ignition switch on, press accelerator pedal to floor rapidly 3 times, start engine and light should go out. Do not press more then 3 times as then it will not reset.
turn the ignition key on and press the gas pedal 3 times, turn off the key, and start up as normal..this should do it....
With the key on engine off (koeo) depress the gas pedal 3-5 times holding for at least 1-2 sec. then turn key off and start vehicle light should go off. NOTE: on some models y…ou may half to do the same process with the key in the off position.
Turn the key to the ON position without starting the engine. Pump the gas pedal 3 times within 5 seconds. You should now be back at 100%. Book says: The BCM doesn't know the …oil was changed. It is a manual reset. Follow these instructions: 1) Turn the ignition to ON/RUN, with the engine off. 2) Press the information and reset buttons on the Driver Information Center (DIC) at the same time to enter the personalization menu. 3) Press the information button to scroll through the available personalization menu modes until the DIC display shows OIL-LIFE RESET. 4) Press and hold the reset button until the DIC display shows ACKNOWLEDGED. This will tell you the system has been reset. 5) Turn the key to LOCK/OFF.
Turn the key to on position, push the gas pedal to the floor three times, you should see the indicator screen flash, turn the key to off. You should be reset.
Hi, 1. With the ignition key in RUN but the engine off, repeatedly push the trip/reset button (on the dash) until OIL is displayed on the Driver Information Center. 2. Wh…en OIL is displayed, push and hold the trip/reset button for 5-10 seconds. The number will disappear and be replaced by 100 (indicating 100% oil life remaining). 3. Turn the key to OFF. If the change engine oil message comes back on, the engine oil life monitor has not reset. Try repeating the procedure.
It's been a long time since I had a Venture, but if I rememberright, you scroll through the menu until you get to that selection,then you press and hold the button until it re…sets.