0
- disconnect battery cables
- drain the cooling system
- remove drive belt (4 cyl) or water pump drivebelt (6 cyl)
- (4 cyl instructions)
- remove right front wheel and splash guard
- remove water pump pulley
- remove bolts attaching water pump to engine block and then remove pump. if stuck tap w/ rubber mallet
- clean the bolt threads, remove all gasket (w/ sandpaper, or removal tool) scrap off sealent.
- (6 cyl)
- remove air filter housing
- remove water pump drivebelt tensioner
- remove water pump mounting bolts and water pump
- clean the bolt threads, remove all gasket (w/ sandpaper, or removal tool) scrap off sealent.
- (last steps for both models)
- apply rtv sealant, gasket
- mate pump to housing
- install bolts (89 in-lbs torque)
- reinstall belt, fill cooling system, reattach battery
Wiki User
∙ 14y ago
Wiki User
∙ 11y agoLook for lower radiator hose. This should be attached to it. Should be under fan pulley front of block. Just remove fan/belt/pulley and then pump with appropriate sized sockets and pull off front of block. Lossen any belts on this pulley by using adjustment bolts on accessory brackets. (look for a bolt in a slot near alternator for example) Should be about 8 bolts total-all SAE. Remove lower hose by loosening clamp with a screwdriver (worm drive) or pliers (pinch type) You will lose some water. Just top off rad when done. Before you put new pump on, you will have to clean off gasket mating surface and use a new one (gasket-should be with pump) when replacing it with a little blue rtv thinly smeared on mating surfaces and end of pump bolt threads in case any go through water jacket. (They do on some engine blocks). Replace belts, hold accessories tight with a long pry bar and tighten accessory bolts. You are done.
Wiki User
∙ 11y agoPurchase a Haynes or Chilton's service manual and follow the step by step directions.
1. Diconnect the negative battery cable 2.Drain the cooling system 3.disconnect the hoses at the pump 4.remove the drive belts 5.remove the Power Steering pump bracket. 6.remove the shroud and fan 7.unbolt and remove the pump. TO INSTALL 9.clean the mating surfaces thoroughly 10.using a new gasket, install the pump and tighten bolts to 13 ft. lbs. 11.reinstall all componets in reverse order. 12.after complete operate the engine with heater control valve in heat position until the thermostat opens to purge any air in system check coolant level and fill as required.
Wiki User
∙ 8y agothe library has chilton repair manuals,i just copy the page,pages that i need for .10 cents a copy
Wiki User
∙ 17y agoLike most engines, it is located in the block of the engine. Follow your radiator hoses to the block. The top is where your thermostat is and the bottom is where your water pump is.
Add your answer:
Earn +20 pts
How do you replace the water pump on a 2004 Kia Rio 1.6L DOHC?
How do you replace the water pump on a 2004 Kia Rio 1.6L DOHC?
How do you replace a fuel pump on a 2000 Ford E150 cargo van?
Dump the gas tank out of it. the fuel pump there.
Water pump making noise?
The bearing is on its way out. Replace the pump soon.
To replace the water pump on a 1990 Honda Accord should you go under the car to locate it better or take the drivers side front wheel off?
THE WATER PUMP ON THE ACCORD IS DRIVEN BY THE TIMING BELT AND YOU WOULD NEED TO REMOVE AND REPLACE THE BELT AT THE SAME TIME AS THE WATER PUMP
Ford ranger water leak at timing chain cover?
Check to be sure it isn't the water pump.
How do you replace a water pump for a 2001 Ford Ranger?
how to replace water pump on 2001 ford ranger
How do you replace water pump on a 2001 Ford Focus?
how to replace water pump on 2001 ford focus
Replace a water pump in a 2002 ford escort?
how do you remove the water pump in a 2002 ford escort
How do you replace a 2005 Ford Freestar water pump?
how can ford freestar 2004 water pump be replaced
How do you replace water pump in 93 6 cylinder ford econoline van?
how to replace water pump in 93 ford econoline 6 cylinder ford van
How do you replace water pump on 2004 Ford Taurus?
The water pump on the 2004 Ford Taurus will be replaced by removing the right front wheel to reach the water pump. You will disconnect all hoses to the water pump and replace the pump and put the hoses back on the new pump.
Where is the water pump on 2000 Ford Focus?
do I have to lower the engine to replace the water pump ona 2000 ford focus zetec engine
Replace water pump on 1999 Ford Ranger?
very carefully.
Where is the water pump located on a 1993 Ford Thunderbird?
The water pump is located in the middle of the front of the engine. The water pump is fairly easy to reach and replace.
Can the thermostat on the ford contour cause water to come from the water pump?
No. A leaking coolant pump is caused by a worn seal inside the pump. You will have to replace the pump.
How do you stop your water pump leaking on your ford transit lorry?
The way you stop your water pump from leaking on a Ford Transit Lorry depends on why it is leaking. The most common fix is to replace the gasket on the water pump.
When should the water pump be replaced on a ford ranger?
Only replace the water pump if you have a visible external leak, the water pump bearings are bad, or the shaft is broken.
