0
first of all you crazy if you dont know how to do that
You will need a Power Steering pulley puller, no joke.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Removing pully from power steering pump do you need to remove the pump or is there a trick to it?
To get the pulley off requires a pulley puller to do it. You do not have to remove the PS pump to do it. It also takes a special tool to put the pulley back on too.
Where is the oil pressure switch located on a 1998 Ford Windstar 3.8 liter 6-cylinder?
96 windstar 3.8 oil pressure switch is located under power steering pump. Remove serpentine belt and alternator. Remove PS pump pulley with special puller to get access to PS pump bolts. Drain PS pump and remove PS hoses. Remove PS pump.
How do you remove the power steering pump on a 1994 Chevy Corsica?
Loosen, then remove the belt. Shine a light through one of the holes in the PS pulley and turn it slowly. You will see three bolts through the holes. Use a 13mm socket and a swivel to unscrew and remove these bolts. Lift the pump out of position and remove the hoses. Use a Power Steering Pulley Puller to remove the pulley. This puller grips the pulley by its center hub. Any other type of puller will destroy the pulley and then you will need a new pulley.
Can you skip removing the PS Pulley and just remove the entire pump to access the WP Bolt?
This is on a 1998 Olds. Intrigue 3800 V6
How do you remove pulley from 1997 Olds 88 LS 3800 so you can get to power steering?
If you stick your finger in one of the holes on the pulley and rotate it around at approximately 1 o'clock and 6 o'clock positions you will find the bolts that hold the power steering pump on. to remove the pump from the engine you just slip a socket through the hole.AnswerThe pulley is pressed on your PS pump. You will need to rent the correct puller to remove the pulley.
How do you replace a power steering pump on 1997 F150 4by4?
You will need a special puller to remove and replace the PS pulley. If you attempt to do this without the special tool you will damage the new pump and/or the old pulley. The rest is straight forward.
How to remove PS pump pulley from 1999 73 diesel?
The grove on the front of the pulley requires a sleeve in a u shape that slides over the pulley grove and a fine threaded bolt is part of the the sleeve assembly than you tighten the bolt which in turn pushes on the pump shaft removing the pulley. They are avaible at NAPA Stores
How do you replace a power steering pump on a 1999 ford escort?
1. Remove the PS pump reservoir. 2. Remove the PS pump pulley. 3. Raise and support the vehicle. 4. Remove the 6 bolts and right hand splash shield. 5. Disconnect the PS pressure hose. 6. Lower the vehicle. 7. Loosen the clamp and remove the PS reservoir to pump hose. 8. Remove the 3 bolts and remove the PS pump. Installation: 1. Install the PS pump. 2. Raise and support the vehicle. 3. Install the PS pressure hose. 4. Install the RH splash shield. 5. Lower the vehicle. 6. Install the power steering pump pulley. How to bleed the PS pump of air. 1. Fill the reservoir with Mercon AFT. 2. Raise and support the vehicle. 3. Disconnect the electrical connector to the coil. 4. With the starter operating move the steering wheel lock to lock several times. 5. Make sure the reservoir is full of fluid at all times. It is essential that the weight of the vehicle not be on the steering system to bleed the air from the pump.
Jeep Wrangler serpentine belt replacement?
There is a tensioner under the power steering pump. Lossen the pulley with a 15MM socket .. Do not remove it ... On top of the bracket to the left of the PS pump there is an adjustment screw again 15MM lossen it as well and the tensioner pulley will provide slack in the belt....once there is enough slack in the belt remove it make notes on how the belt is routed on the Alt,AC etc.... Replace with a new belt and tighten the adjustment screw until proper tension is on the belt then tighten the tensioner pulley below the PS pump. This is for a 98 Wrangler TJ...
Can you replace just the pulley on the power steering pump for a 98 Plymouth voyager?
Well!? I am just going through the hell with this problem. Pulley is made out of plastic compound - bakelit. You will have to remove a drive shaft in order to take a pump with the pulley out. You need a special pulley remover to do the job for you - on your work bench. Another option is braking the old pulley and chipping the pieces out. Mounting a new pulley is a another issue. You will need a compressor and a pneumatic gun to mount a new pulley on the shaft of the PS pump.
How do you remove the oil pump on a 1997 Camry 4-cylinder?
You have to remove the alternator, driving belts (serpentine belt, stirring pump belt). After that remove the engine mount on the passenger side of the car (do not forget to put something underneath the engine before removing the mount). After that you need remove the upper timing belt cover. Remove the crankshaft pulley and lower timing belt cover. Put the marks on the timing belt. Loosen the timing belt pulley, stretch the spring, and tighten the timing belt pulley. Remove the timing belt. After this you get access to the oil pump, which is going around the crankshaft and has dozen of bolts to remove. PS: Before you start make sure you have to gasket because they are not reusable.
Why is 95 Kia Sephia power steering pulley wobbling?
Bent shaft, replace PS pump
