answersLogoWhite

0


Best Answer

simple process. 1st press and hold buttons 1 and 3 till the light blinks rapidly. this clears out any old codes already stored. 2nd press and hold which ever button you want the remote stored to. while pressing the button on your discovery press and hold your garge door remote. and place it as close as possible to the uint on your discovery. continue to hold both buttons until there is a slow blink on the unit. Should be all set at that point.

User Avatar

Wiki User

15y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you program the built in garage door opener in your 2002 Disco?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you program Ford explorer 2008 garage door opener?

Built in Explorer garage door openers are Homelink brand. Go to Homelink and it will ask you for vehicle information and garage door information. It will provide the exact step by step.


How do you set the garage door opener for a 2000 Jaguar XK8?

Short answer: Hold the built-in button down and your garage door remote control button down at the same time and near each other. The built in will flash slow then fast once it gets the code (takes up to 1 min). - that's it - but... I have a Genie Garage door opener and remote and I had some problems that figured out (don't want to rewrite it here) so I cut and paste this: (sent to Genie) Just wanted to let you know that I figured out how to use my XK8 built-in garage door opener but there was a glitch that I had to work through. I actually had to program the built in remote with my Genie Intellicode Transmitter (GIC/GIT-1,2, or 3) (that worked to program my built-in remote but it wouldn't work on the genie pcg650 garage door opener?) I then used your Rcvr Programming Instructions to program the "genie pcg650 garage door opener receiver" with the cars built-in opener (that I had just programed with youf Intellicode remote. Beleive it or not when I was all done the intellicode remote and the Car's built-in remote both worked. It was like the built-in remote got the correct code but the receiver had to learn that it was OK to accept it from the built-in? Anyway, your sight helped a little and I thought you could help others with this info. Thanks Danny


How do you change the battery for the garage door opener on a 2005 300c?

The built in garage door buttons run off of the cars battery.


How do you program a built-in opener on a 2007 Buick?

Open and read your owner's manual.


When was garage door opener 139.53635SRT built?

My one of these says it was built in 1993 (and installed in 1996), although I'm not sure the dates it was manufactured between.


What are the 3 buttons on the visor of a 95 Lincoln?

the buttons could be for the built in garage door opener... im not familer with that model but they were used at that time


How do you program the built in garage door opener Buick Riviera?

1. In the car, press and HOLD the outer two HomeLink buttons until the HomeLink light begins to flash rapidly. This will clear any old codes left in the car's controls. 2. Take the garage remote and hold it near the HomeLink buttons. Press and HOLD BOTH the garage remote and one of the HomeLink buttons until the HomeLink light begins to flash rapidly. Now your car has learned the proper garage door code, but you must get "permission" from the garage door opener itself before it will let the Buick open the door: 3. Climb up on a ladder and press the "Learn" button on the back of the garage door opener. WITHIN 30 SECONDS, get back into the car and press the programmed HomeLink button 3 times, for about 2 seconds each time. When the garage light flashes, your code is locked in! (Different door opener power heads have different routine to "learn" the HomeLink remote. Consult your owner manual for the door opener power head to program it to learn mode.) More specifics are available at homelink.com.


If you don't have a manual how do you program garage door opener for 2003 Kia Sedona?

Call a dealer, someone in the service/parts dept. should know how to do it. If you have a HomeLink system (built into overhead console), you can find programming instructions at their website: http://www.homelink.com/training/train.taf


How do you program the built in garage door opener in a 2001 Sebring Convertible?

I have a 1998 Sebring that has 3 buttons on the drivers sun visor. First find the program button on your garage door opener motor head. When the button is pushed a little red light should start flashing. Now you have a cetain amount of time, usually between 15 and 30 sec., to push and hold the desired button in your auto. Hold the button until the little red indicater light starts flashing. Sometimes it is best to have help. Sometimes the auto has to be with in 10 feet and sometimes outside the garage. A little trial and error will work. Mike


What is the difference between a built-in garage and an attached garage?

A built in garage has living space above it. An attached garage has no living space above.


How do you program the built in garage door opener in a 1998 Mitsubishi Diamante?

Im not sure if it is the same automatic opener that I have in my Diamante, its a 97, and I had the same question you did about mine.....until today......Its WAY too complicated to explain how to program but I will hopefully send you in the right direction so you can hopefully find the right info for your car...... Go to your local library, and ask to use a program called "alldata"...Its has all the info you need about your car and more.....just type in the Model, Make, and year, and it will bring up everything from electrical diagrams, to maintainence tips and solutions......GOOD LUCK!!!!


How to Repair a Garage Door Opener?

Garage doors that open automatically are one of those conveniences we take for granted. When a garage door opener suddenly stops working, it can be extremely annoying. Here is a step by step guide to fixing your garage door opener. First, you should check to see if the cord that feeds power to your garage door opener is actually plugged into an outlet. This may seem too obvious, but this is a common reason why garage door openers do not work. If that doesn’t fix the problem, check your owner’s manual for some kind of lock feature. Someone may have inadvertently activated the lock feature, and that feature may be preventing the door from operating. The manual should tell you how to turn the lock feature off. If that doesn’t work, try unplugging the garage door opener and then plugging it back into an outlet a few times. This may reset the censors, allowing the opener to work again. If that doesn’t work, you should perhaps check to see if the batteries in your remote control for the garage door opener haven’t run out of power. If it still doesn’t work with new batteries, it is possible you accidently deprogrammed the remote control. Check the owner’s manual to learn how to reprogram it. If that didn’t fix the problem, check to see if the beam censor for your garage door opener is plugged in correctly. Next, try cleaning the censor itself. Its possible dirt, grime, or dust may have built up on the censor, preventing it from sending the signal to activate the garage door’s motor. Lastly, you should check to see if the chain that lifts up the door has been broken or become loose. If so, it is unfortunately not safe for you to try to repair it on your own. You should call an electrician who specializes in garage door repair. Until the repair man arrives, you are going to have to manually open the garage door yourself by either using a release cord or a handle. With these simple steps you can easily trouble shoot most problems that prevent a garage door opener from operating yourself.