a. Press and hold the VCR•DVD
key. The illuminated ON•OFF
key turns on.
b. While holding down the
VCR•DVD key, press and
release the number 2 key on
the keypad to control a VCR or
the number 3 key to control a
DVD. The illuminated
ON•OFF key turns off.
c. Release the VCR•DVD key.
The illuminated ON•OFF key
blinks four times and then
turns off. Your remote is now
either in VCR or DVD
Programming Mode,
depending on which you
chose. Proceed to step 4.
4. Press and hold the component key
(TV, VCR•DVD, SAT•CBL) you
wish to program. The illuminated
ON•OFF key turns on and
remains on.
5. While holding the component key
down, press and hold the ON•OFF
key. The illuminated ON•OFF key
turns off.
6. After holding down both keys for
three seconds, the illuminated
ON•OFF key turns back on.
7. Release both keys. The illuminated
ON•OFF key remains on.
TIP: Throughout the programming
of each key, be sure to keep the remote
pointed at the IR sensor of the
component you are currently
programming the remote to control.
8. Press and release the PLAY key,
then wait five seconds to see if
your component turns off. If your
component does not respond,
continue to press the PLAY key
every five seconds until your
component turns off. Each time
you press the PLAY key, the
illuminated ON•OFF key blinks
and a block of 10 codes are sent to
your component. This process
continues until all of the codes in
the Code Lists have been searched.
(If your component has not turned
off after all codes have been
searched, the illuminated ON•OFF
key blinks four times and turns
off. The Auto Code Search Entry
method is exited.)
9. When your component turns off,
you know the correct code is in
the last block of 10 codes sent.
Press and release the REVERSE
key. Wait two seconds to see if
your component turns on again. If
your component does not respond,
continue to press the REVERSE
key every two seconds until your
component turns on again. This
will isolate the correct code in the
last block of codes sent. Each time
the REVERSE key is pressed, the
illuminated ON•OFF key blinks.
Note: If you accidentally press
the REVERSE key after your
component responds, press and
release the FORWARD key. Then,
wait two seconds to see if your
component turns off again.
10. Once your component turns off,
you have found the correct code.
You must save the new code by
pressing and releasing the STOP
key. The illuminated ON•OFF key
turns off. You must press the
STOP key to save the code or the
correct code will not be stored!
The following directions I found worked for me to program my crk76ad2 remote:
Turn on the component you want to program.
2 Press and hold both the TV/DVD/ect button and the power button until the light comes on and stays on
3 Press the play button every 5 seconds until the device turns off. A bank of ten codes is being sent each time.
4 Press the rewind/reverse button to see if it turns off/on again. Wait 2 seconds and press again until it turns back on.You may have to do this up to 10 times until it searches through the bank of ten codes sent.
5 Press and hold the stop button until the light goes off. This saves the code.
Found the instructions at: http://www.wikihow.com/Program-an-RCA-Universal-Remote-Without-a-%22Code-Search%22-Button
What is the code for an Emerson Tv to RCA converter box?
how do i program a charter remote to a rca tv
how to program my tv with the RCA D 770 - universal remote control which has no code search button
139 press program. Enter the 3 digit number (139) and press ok.
what is the code to program a RCA remote and a motorola cabel box
how to program a universal rca remote to a dtv craig converter box
Rca remote
i need to progra a rca system blink 4 remote to my westinghouse tv how do i do this
i have a rca remote without any light, have a quasar tv, how do i make this work?
The best thing to do to program your RCA remote is to follow the directions you were given when you purchased it. Each universal remote is slightly different, so your best bet would be to follow the instructions you were given at time of purchase.
This model was sold with many RCA TV's. Retrevo has a manual for an RCA RBA29550 that uses this remote. Jump to page 8 to see how to program it.
Try purchasing the manual.