0
Very complicated formula Try seeking out a 2nd year apprentice as the UA has books with these formula's which are seldom used
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
How do you figure a 7 foot horizontal rolling offset?
A rolling offset is generally an offset requiring a change in 2 directions. Eg. A horizontal offset and a vertical change in elevation. There is additional information required to answer the question. What is the angle of the fittings being used for offset? 15 deg. 30. 45? What is the change in elevation? If this is a flat (no change in elevation offset) using 45 deg., the offset dimension (7') is multiplied by 1.4142 which is the secant and cosecant of 45 deg. The result 7 ' x 1.4142 = 9'-10 13/16" Again, this result is for a flat run of pipe. If we have a rolling offset with a change in elevation of say 1'. We can use the Pythagorean theorem (A2 +B2 = C2) The result would be (1')2 + (9'-10 13/16")2 = 98.99812 sq. ft. The square root of 98.99812 is 9'-11 3/8"
What is the meaning of TOE in pipe fitting?
Threaded On End
What is the fabricated pipe and pipe-fitting industry dependent on?
The U.S. fabricated pipe and pipe-fitting industry is strongly dependent on the health of the domestic construction industry, which, after enduring rough economic conditions in the late 1980s and early 1990s, rebounded in the mid-1990s.
What is the difference between schedule and class?
schedule is the thickness of the pipe and class is pressure/temperature rating of a fitting or pipe
What is a dogleg offset pipe?
Type your answer here... Generally its a non-enginered angle in a piping weld joint occurring in the axial run of pipe.
What is an offset in pipe fitting?
Using fittings to change centerline of pipe.
What does tos stand for in pipe fitting?
what are some pipe fitting abb
How do you figure a 7 foot horizontal rolling offset?
A rolling offset is generally an offset requiring a change in 2 directions. Eg. A horizontal offset and a vertical change in elevation. There is additional information required to answer the question. What is the angle of the fittings being used for offset? 15 deg. 30. 45? What is the change in elevation? If this is a flat (no change in elevation offset) using 45 deg., the offset dimension (7') is multiplied by 1.4142 which is the secant and cosecant of 45 deg. The result 7 ' x 1.4142 = 9'-10 13/16" Again, this result is for a flat run of pipe. If we have a rolling offset with a change in elevation of say 1'. We can use the Pythagorean theorem (A2 +B2 = C2) The result would be (1')2 + (9'-10 13/16")2 = 98.99812 sq. ft. The square root of 98.99812 is 9'-11 3/8"
What is meant by fitting allowance?
The fitting allowance is the difference: (pipe end to fitting center measurement) minus (pipe end to end measurement). It is the amount of length the fitting adds to the end of the pipe (to get the center of the turn).
What is Chelyabinsk Pipe Rolling Plant's population?
Chelyabinsk Pipe Rolling Plant's population is 8,000.
When was Chelyabinsk Pipe Rolling Plant created?
Chelyabinsk Pipe Rolling Plant was created in 1942.
What is the formula for a rolling offset with 2 45's?
There are many types of rolling offsets. 2 common are rolling offset using 45 degree fittings and a rolling offset using any angle. using 45's Rise: elevation change roll: run of the pipe moving to the left or right Travel: the run of pipe to make the offset Simple formula Travel = SQRT((rise(squared) + Roll(squared) ) x 2) rise = 10" roll= 16" Travel=? travel= SQRT ( ((10 x 10) + (16 x 16)) x 2 ) travel= SQRT ( ((100) + (256)) x 2 ) travel= SQRT ( ( 356 ) x 2 ) travel= SQRT ( 712 ) Travel= 26.68333 or 26-11/16"
How do you work out x dimensions?
measure the length of the fitting first. Then insert pipe into fitting and mark a line on pipe. measure that bit of pipe. deduct off the length of fitting and half it to give you your x dimension
What nicknames does Adam Fitting go by?
Adam Fitting goes by Pipe.
What type of fitting do you use to connect PVC pipe to unthreaded galvanized pipe?
You can't. There is no fitting to do this. Galvanized has to be threaded.
What are pipe fitting used for?
To join lengths of pipe and to route it where it needs to go.
What is the pipe fitting formula for a 22.5 degree?
Pipe size times 0.707
