You can connect your standard definition TV to your satellite receiver in a couple of ways. First, if your TV has composite video/audio inputs (yellow, red, and white RCA jacks), you can connect to these inputs using the composite video outputs of the satellite receiver. Another alternative is to use the standard coaxial cable output from your satellite receiver to connect to the 75ohm antenna input on your TV.
*Note: Neither of these connections will display high definition programming on your standard definition TV. The TV is only capable of standard definition, so you will see a clear picture, but it won't be true high definition, regardless of the input signal's definition.
Connect the satellite receiver to the surround receiver. You can then use the receiver to switch between this source and the the DVD or Blu-Ray player.
check first your satellite receiver if there is an HDMI jack. connect your HDMI cables from your satellite receiver to your tv tuner. if you don't have the HDMI jack, check the AV output jack. connect the AV cables from your satellite receiver to your tv tuner. you can use either AV or HDMI.
A satellite dish is designed to connect to a satellite receiver unit. Generally they are dedicated devices. There are a few satellite receiver cards or devices that can be installed into a computer and will operate as a video input card for the computer. These are specialist devices and will not be found as a standard feature on any computer. Normally, to capture a video feed, the output form a dedicated satellite receiver would be connected to a video input port on the computer. Again, the video input is a specialist device typically used in video editing and not usually found as part of a standard computer set up.
no yes
You could use an external cable or satellite receiver and connect speakers to that.
This depends on the brand your satellite tv receiver is. If your receiver is for example, Dreambox, than you could connect it to a computer via the RS232 port or via the ethernet port located on the Dreambox receievr. On other brands, this may be different. On some brands you can not connect a tv receiver to a computer. So this is different for all receivers. Also, some special softwares would be needed to establish the conenction between computer a receiver.
Since your satellite receiver is not HD, you can use either a coax cable or an RCA cable to connect to your TV. The Wii can plug into a composite port. If you only have 1 RCA/composite connection on your TV, you can get an A/B switch so you can have both devices connected so you can switch between the two devices.
Dreambox works like all satellite tv receivers work. It decodes the signal coming from the satellite and allows you to watch satellite tv channels on your tv. You connect the dreambox to your satellite antenna, than connect it to your tv, and do an auto scan, and you can watch satellite tv channels on your tv. Almost all Dreambox are HD, so you can watch HD channels using dreambox receiver. Dreambox is a more advanced satellite receiver, allowing users to gain more control over the receiver and uses advanced softwares and ecryptions. This is why it is considered to be among the best satellite tv receivers.
A HD TV has HD video ports and an RCA or Coaxial cable video ports on it. The HD video ports are colored red, green, and blue, and since you have a standard definition satillite receiver, you won't be using them. RCA ports have red, white, and yellow tips, with the yellow cord transfering video and the red and white cords carrying sound. These should be located near the red, green, and blue video ports for the HD connection. A Coaxial cable connection has a chrome screw-like ext
The fit a cable to an external aerial dish, one must check the satellite receiver to find the coaxial socket. Connect the cable from your satellite receiver to the external antennae socket.
this is not possible with direct tv in an obvious reasons. however, you can do this with dish network. before you connect your vcr to record satellite tv program, check first if your VCR has an HDMI input. if you found an HDMI input slot, then you are good to go. connect your satellite receiver to the HDMI input slot of your vcr then attach the AV cables from your VCR to your television.
check your surround sound if it has an HDMI or AV input jacks. if it has, then you are good to go. from your satellite receiver, attach the HDMI cable or AV cable. connect it to your surround sound. after connecting the satellite receiver box and surround sound, attach the HDMI or AV cable from the surround sound to your television.