0
The only true way to add a ground to an old metallic fixture is by drilling a hole and installing a self threading UL Listed ground screw through a metallic part on the inside of the light fixture. Make sure the surface where the grounding conductor is to be attached under the new screw is clean from any Paint, Tarnish or Rust. Use Emory cloth, sandpaper or a file to do this as it must be a bare metal connection. If you can't find Self threading Ground Screws you can get Electrical Screw tapping tool at your local hardware store and thread your hole for a regular ground screw. You must make sure that all metallic parts of the fixture are grounded or it will become an electrical hazard. If it is going to be outside I would strongly suggest putting it on a ground fault circuit for extra protection. GFCI's measure changes in the circuit to determine if power has leaked from the Fixture/Circuit to something or someone. The best solution is to remove the fixture from service and replace it with a close modern replica.
Wiki User
∙ 9y ago
Add your answer:
Earn +20 pts
How do you add another porch light to an existing switch?
Piggyback off the box for the existing light. Run a wire from the existing junction box to a new junction box (which is placed wherever you want the new fixture). Then, in the existing box, connect the wire coming from the switch, the wire for the existing fixture, and the wire for the new fixture together using wire nuts. Wire up the new fixture, and presto, you have two fixtures on a switch where there was only one before.
How do you wire light fixture with three wires when there are two house wires?
CAN'T. Must have 3-wire w/ground. [First off, I want to admit that the wording of this answer is skewed. However, if you read the answer you will understand why. It is techinically correct in terms of the NEC. -TJNII] The idiot that wired my house did this. To add insult to injury he connected the hot to one circuit and the neutral to another. I was almost electrocuted because of it. Do it right or don't do it at all. Your negligence may kill someone.
How do you remove the light bulb from the underwater light?
You need to remove the screw that holds the light ring and pull the whole light fixture out of the water and up onto the deck. There should be enough wire wrapped around the back of the light to allow this. Remove the lens, replace the bulb, and reinstall the lens with a new gasket, being careful not to get any water inside the fixture. Wrap the excess wire around the back of the light fixture and replace it in the niche, securing it with the screw. A. I would add: You need to test the GFCI, the wiring of the whole fixture - continuity test. If this is a fairly old fixture - my decision would be to replace the entire assmebly with a new one. If you have no GFCI then would be critical that you add one. And lastly but not least, you should have a pool tech service the light. He will know what to look for and how to correct any situation with your light. If there is something wrong with your light assy. and you do not find it by testing you put yourself and anyone who uses the pool in a great deal of danger if the light should malfunction. The codes specify that anytime you work on a pool light you then need to bring that product to current code. That also includes the main drain grate. Yes if you or a pool tech works on any portion of the pool for repairs the code demands that the main drain be brought to current code requirements. So it is not only a matter of just changing the light bulb and gasket.
How do you hook up two light switches on one single home run?
I can probably answer this question but to do so I need more info; switchleg from where another light? And why are you switching it again? or are you adding a light? Respond to my message page and I'll try to answer it further. I am hooking up a light fixture in an add on closet. I am feeding from the light in the bedroom, and I want to control the closet light from a switch just out side the closet door.
How do you convert a two pin plug to a three pin plug?
You don't, in theory, because the ground wire is missing. But if you must, cut the end of and add the new three pin plug, the two flat pins are for the two wires, the round is for the ground that is missing. If something has only two wires,say a light fixture, adding a plug that has the three is useless because the ground wire is missing, so it does not become safer just because you added it. If the end is bad,then you get a plug end that comes apart and is made for adding to a wire, do not cut wire,add another plug end by splicing it together with electric tape.
Can you convert a flush mount light fixture to a pendant light fixture?
Yes. The Home Depot has a kit for about $10 that converts a recessed can to accept a standard fixture. Weight limit is about 10 pounds.
How do you wire a pull switch on a hard wire ceiling light that has no switch?
Two options. Change the fixture to a keyed pull-chain, or add a pull-chain adapter to the existing fixture. Both available from Home Depot and others for about $3.
How do you add another porch light to an existing switch?
Piggyback off the box for the existing light. Run a wire from the existing junction box to a new junction box (which is placed wherever you want the new fixture). Then, in the existing box, connect the wire coming from the switch, the wire for the existing fixture, and the wire for the new fixture together using wire nuts. Wire up the new fixture, and presto, you have two fixtures on a switch where there was only one before.
How do you wire light fixture with three wires when there are two house wires?
CAN'T. Must have 3-wire w/ground. [First off, I want to admit that the wording of this answer is skewed. However, if you read the answer you will understand why. It is techinically correct in terms of the NEC. -TJNII] The idiot that wired my house did this. To add insult to injury he connected the hot to one circuit and the neutral to another. I was almost electrocuted because of it. Do it right or don't do it at all. Your negligence may kill someone.
What is the standard distance between the ceiling and a wall mounted light fixture in a bathroom?
The height is usually based on the type of mirror that is to be installed above the sink. Take the height of the sink plus the height of the mirror and add 6 inches to find the center for the placement of the fixture junction box. If there is to be a space between the sink and the mirror add that measurement in to factoring of the height.
Fluorescent Light Fixtures?
form_title= Fluorescent Light Fixtures form_header= Add light to your home with fluorescent light. How many fixtures do you need?*= {1, 2, 3, 4, 5, More than 5} Is the fixture for a drop ceiling?*= () Yes () No Do you want the fixtures delivered?*= () Yes () No
Can you use a 125v unnotched cable with a notched socket 120v ballast for your 1000 watt HID light fixture if you add a notch to the cord or remove the notch from the socket?
See discussion page for more.
How do you remove the light bulb from the underwater light?
You need to remove the screw that holds the light ring and pull the whole light fixture out of the water and up onto the deck. There should be enough wire wrapped around the back of the light to allow this. Remove the lens, replace the bulb, and reinstall the lens with a new gasket, being careful not to get any water inside the fixture. Wrap the excess wire around the back of the light fixture and replace it in the niche, securing it with the screw. A. I would add: You need to test the GFCI, the wiring of the whole fixture - continuity test. If this is a fairly old fixture - my decision would be to replace the entire assmebly with a new one. If you have no GFCI then would be critical that you add one. And lastly but not least, you should have a pool tech service the light. He will know what to look for and how to correct any situation with your light. If there is something wrong with your light assy. and you do not find it by testing you put yourself and anyone who uses the pool in a great deal of danger if the light should malfunction. The codes specify that anytime you work on a pool light you then need to bring that product to current code. That also includes the main drain grate. Yes if you or a pool tech works on any portion of the pool for repairs the code demands that the main drain be brought to current code requirements. So it is not only a matter of just changing the light bulb and gasket.
How do you add a light and switch?
for USA, Canada and countries running a 60 Hz supply service.Do this electrical work only if you feel confident that you can do it safely. If not then this is the procedure that an electrician would use and you would be able to follow what he is doing. Again an electrician should be your first choice. If you consider doing this the first thing is SHUT THE CIRCUIT'S BREAKER OFF.Light fixtures can be fed out of receptacle outlet boxes. To the light switch, two wires will go from the wall receptacle, connected black to black and white to white and ground to ground, to the new light switch and then two more wires will leave the new light switch and proceed up to the light fixture box. In the switch box first connect the incoming and outgoing ground wires to the ground screw in the new switch box. Next the white wires will be spliced together with a wire nut and pushed to the back of the box and then the two black wires will be connected across the switch. Pre position the switch in the off position, which is the handle down, before attaching the wires. The "hot" incoming wire connects to the top screw of the switch and the black outgoing wire that goes to the light fixture box connects to the bottom screw of the switch. Be sure to connect the ground wire around the grounding screw in the light fixture box. When the switch is turned on the voltage is applied to the fixture junction box.See View Discussion below.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energizedIF YOU ARE NOT REALLY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
How to Decorate Using a Sconce Light Fixture?
If you need to add light to a room in your home, consider using a sconce as an additional light fixture. A sconce is a wall mounted light fixture that can add style and grace to your room while at the same time providing additional illumination. A lot of people overlook the lighting in their rooms to the detriment of their decor. Good lighting makes a tremendous difference in how a room looks, changing it from dark and drab, to warm and welcoming. Not only this, but a room with good lighting always looks bigger than it is, an illusion that people with small rooms can take advantage of. When adding a sconce as a light fixture to your room, you will encounter two main varieties. The first kind of light fixture that is available is a sconce that shines light by use of candles. These sconces are easy to install and inexpensive. One drawback, however, is that they can be inconvenient if they are being used as the main lighting source in the room since you would have to light each candle every time you needed light. Also, you would have to factor in the cost of replacing the candles over the lifetime of the light fixture. Not only this, but candle powered sconces can be fire hazards since they involve open flames. Instead, opt for electric sconces. You will pay more for these up front, but an electric light fixture looks much more professional. Not only this, but they are more convenient and safer to use. When you install your light fixture, you’ll want to consider the placement of the sconces. Sconces are traditionally used to frame a focal point in the room. For example, if you have a cherished piece of art that you want to serve as the highlight of you room, you can place two sconces on either side of the piece of art, which will envelope it in a soft light that will make it stand out from the rest of the room. For a more dramatic look and to illuminate the whole room, you can place a series of light fixtures, spaced evenly, along a wall. This will create a series of bright and dim spots that can make your home look like an art gallery. Finally, consider placing a light fixture next to a doorway or threshold for a classic and elegant look. If you need better lighting in your home, consider adding a light fixture like a sconce. Their versatility and great style can improve the look of any room.
Two Tips On How To Choose Modern Light Fixtures For Your Living Room?
Modern light fixtures are great for anyone who wants to add an elegant look to their living room. There are many different styles being sold today. Let's take a close look at three two tips on how to choose modern light fixtures for living area within your home.ColorYou should select a modern light fixture that matches the color of the walls within your living area.StyleIt is imperative that you choose a fixture that matches the style within your living room. For example, a modern light fixture will only complement a living area that has a contemporary look.Following the two tips listed above can help you select appropriate modern light fixtures for your living area.
Can you add a receptacle to an end of run switch?
No, the neutral conductor will not be in that box. The white wire in the end of run will be the return "hot" leg back to the light fixture. When wired this white conductor should have had a black tape marker put on it to signify that it was not a neutral conductor. That same conductor should also have had a black marker placed on the end in the fixture's junction box.
