0
Equalizing lines should be located in multiple condenser and compressor applications where Between condenser and evaporator coils or Near the TXV or Between compressors and condensers or None of them?
Bowsport
oppisite side of txv sensing bulb on outlet of evaporator (suction line)
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Applications of synchronous motor?
It is used in variety of applications such as... · Machine Tools such as a ball mill · Motor generator sets · Synchronous clocks · Timing devices · Synchronous condensers to condition electrical power · Record players · Robotics
How are steam condensers classified?
Two broad types of condensers are: (i) Direct contact type condensers; where the condensate and cooling water directly mix and come out as a single stream. (ii) surface condensers; which are shell and tube type heat exchangers where the two fluids do not come in direct contact and heat released by the condensation of steam is transferred through the walls of the tubes in to the cooling water continuously circulating inside them
How we measures strain using microcontroller?
Measuring strain using micro-controller is simple and easy. When measuring using micro-controller you use points and condensers.
What is kenotometer?
A kenotometer is an instrument used in steam turbine condensers to measure the vacuum in the steam space of the condenser. The vacuum achieved by the condenser has significant influence on the efficiency of the steam turbine.
Why steam is to be condensed in thermal power plant Y should not you use a compressor to suck compress and send back the steam at high pressure?
It's a matter of the steam cycle, the condenser in a condensing power plant creates a vacuum, or low pressure zone for the steam to flow into. A compressor would need to compress this steam 650 times plus generate enough force to force it back into the boiler, this would require a lot of energy to do. It is much simpler and much more cost effective (energy wise), to condense the steam and exhaust the excess heat to the cooling tower. The condensed water can then be pumped back to the boiler in stages to repeat the cycle. In these stages the water is de-aerated, treated and heated back to the boiler's temperature to prevent thermal shock in the boiler. In short condensing the steam is easier, safer and cheaper than trying to mechanically compress it. **By the way, there are vacuum pumps called "hoggers" or steam powered ejectors, and injectors which could do just what you suggest, but use exorbitant amounts of energy to do so. These are typically used in conjunction with condensers to eject non-condensible gasses from condensers.
What is the freon capacity on a international 3400 bus 2 condensers with 3 fans each and 2 compressors carrier system?
2 condensers? 2 compressors? Sounds like 2 systems to me.
When does the condensing pressure stop rising?
When just as many vapor molecules condense into liquid as the compressor pump into the condensers.
What are the main components of a slushie machine?
The main components of a slushie machine are plastic mixing bowls in which the beverage is stored, evaporators, compressors, condensers, blades, filter and a thermostat.
The fans that you see on a roof-top chiller are used to cool the?
Condensers
Applications of synchronous motor?
It is used in variety of applications such as... · Machine Tools such as a ball mill · Motor generator sets · Synchronous clocks · Timing devices · Synchronous condensers to condition electrical power · Record players · Robotics
What is the difference between compressor and condensor?
Compressors are similar to pumps: both increase the pressure on a fluid and both can transport the fluid through a pipe. As gases are compressible, the compressor also reduces the volume of a gas. Liquids are relatively incompressible, so the main action of a pump is to pressurize and transport liquids.In systems involving heat transfer, a condenser is a device or unit used to condense a substance from its gaseous to its liquid state, typically by cooling it. In so doing, the latent heat is given up by the substance, and will transfer to the condenser coolant. Condensers are typically heat exchangers which have various designs and come in many sizes ranging from rather small (hand-held) to very large industrial-scale units used in plant processes. For example, a refrigerator uses a condenser to get rid of heat extracted from the interior of the unit to the outside air. Condensers are used in air conditioning, industrial chemical processes such as distillation, steam power plants and other heat-exchange systems. Use of cooling water or surrounding air as the coolant is common in many condensers.
What system uses compression pumps and condensers to the cool air?
Heat pumps use compression pumps and condensers to cool air.
What are the three types of condensers?
shell and tube
Can truck ac condensers be repaired?
Usually not.
What are the uses of condensers?
ano bayanwlng sgot.......
In the electronics industry are capacitors generally referred to as condensers?
Capacitors have not normally been called condensers in the elctronics industry for more than 50 years.
How are steam condensers classified?
Two broad types of condensers are: (i) Direct contact type condensers; where the condensate and cooling water directly mix and come out as a single stream. (ii) surface condensers; which are shell and tube type heat exchangers where the two fluids do not come in direct contact and heat released by the condensation of steam is transferred through the walls of the tubes in to the cooling water continuously circulating inside them
