To do this, you will need to phase shift the single phase power supply into three distinct phases that are 120 degrees out of sync with each other. Phase shifting Transformers can be used for this, but there might be other ways as well.
No, a three phase motor cannot generally be wired to a single phase supply so, to run it on single phase you would need an electronic inverter unit or a rotary phase converter to generate the three phase supply. Such invertors or convertors are generally expensive to buy and the price will depend on the power of the motor.
As long as the power requirements of the equipment that you want to use the motor on are not too high for the biggest single phase motor available, it is usually best to see if you can part-exchange the three phase motor for a suitable single phase motor.
Another answer
Some three phase motors have all their windings brought out to terminals, usually two terminals per winding. So, if the motor has at least six terminals inside its wiring connections box and you can find out for sure that it was designed to be rewirable to run on single phase as well as on three phase - from the manufacturer or a qualified electrical engineer - then you should be able to connect them to run the motor on a suitably sized single phase circuit.
("Suitably sized" means that the circuit breaker and wiring is of the correct size to handle the current needed by the motor.)
<><><>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
.
No, a transformer cannot produce three phase power from a single phase source. You can do this with a rotary phase converter or with an inverter(variable frequency drive)
This depends on the voltage, and whether it is a three phase or single phase transformer.
A single-phase transformer works with a single-phase supply, while a 3-phase transformer is used with a 3-phase supply. A single-phase transformer has 2 wires on the primary and secondary (ignoring taps) while a 3-phase tansformer has 3 or 4 wires on the primary and secondary.
By design are you going to wind the transformer yourself? In your design you need a 5:1 ratio. On the output side of the transformer any two legs of a three phase transformer is considered single phase voltage. Good luck on your project.
Single phasing occurs when one or two of the fuses protecting the load fault open. This is likened to using two legs from a three phase source to provide two single phase feeds, hence the name.
A three-phase transformer bank is often used in power stations because it is easier to construct and transport very large single-phase transformers, compared with constructing and transforming an equivalent-capacity three-phase transformer.
This depends on the voltage, and whether it is a three phase or single phase transformer.
By having a transformer with 3 phase input and single phase out put
Harmonics are really not needed in single phase transformers.
Your question is rather vague. If you are asking what do you call a group of single-phase transformers, connected to supply three phase, then the answer is a 'three-phase transformer bank'.
A single-phase transformer works with a single-phase supply, while a 3-phase transformer is used with a 3-phase supply. A single-phase transformer has 2 wires on the primary and secondary (ignoring taps) while a 3-phase tansformer has 3 or 4 wires on the primary and secondary.
By design are you going to wind the transformer yourself? In your design you need a 5:1 ratio. On the output side of the transformer any two legs of a three phase transformer is considered single phase voltage. Good luck on your project.
Single phasing occurs when one or two of the fuses protecting the load fault open. This is likened to using two legs from a three phase source to provide two single phase feeds, hence the name.
to determine the transformer characteristics...
with an meg ohm meter
A three-phase transformer bank is often used in power stations because it is easier to construct and transport very large single-phase transformers, compared with constructing and transforming an equivalent-capacity three-phase transformer.
Yes, you can use three single phase transformers on three phase applications and interconnect them to serve as a single transformer or you could use one single phase transformer fed from two of the three lines in a step down application.
..the questions does not say wether the 30kVA transformer is 3 phase transformer or single phase transformer..but it is implying that a single phase welding load at 16A per phase is to be connect to it, it is assumed then that the transformer is 3 phase transformer..we assume load is rated 240V.. ..though not much details is given about the transformer voltage specs. but if is rated 3 phase 415/240V, the approx full load current per phase is given by 30KVAx1.3912=41.736A.. ..but if the transformer was rated single phase 240V say, the approx full load current FLC=30000/240V gives 125ampers.. ..if you further devide the FLC by the intended load current.. ..Recommended no of welders per for a 3 phase 415V transformer and assuming single welding sets =41.736/16=2.6..so you can connect max two welding sets to this transformer per phase,..max 6 weld sets can connect at an approx load factor of 76%.. ..for the single phase transformer, FLC/16=125/16, gives 7.8 but is also recommended not to connect more than 6 welding sets to such transformer for the same reasons..